Siemens SITRANS SCM IQ - Industrial Use Note; Security Information

Layout of additional nameplate
-
-
S N°:
-
-
N1A6101234567
13-KB4BO-0369
-
-
-
TÜV 12 ATEX 107540 X / IECEx TUN 12.0028 X
/ TÜV 11.0287 X
Technical data and temperature classes see certificate / operating instructions
Ex tD A21 IP66 T100°C
IS / 1 / AEx / Ex ib / IIC IS / I / A-G
-
II 2 G Ex ia IIC T4 Gb II 3 G Ex ic IIC T6/T4 Gc
TÜV 12 ATEX 107540 X / IECEx TUN 12.0028 X
/ TÜV 11.0287 X
Before commissioning permanently
remove indications of the protection
type which are not being used.
Install per control Drawing A5E00065622D
II 2 D Ex ia IIIC 110°C Db II 3 G Ex ec IIC T6/T4 Gc
NI / 1 / 2 / A-D NI / 2 / AEx / Ex ec / IIC
0518
ARR P3-235866.: F-Nr
X.0001 X / TÜV 12.094012 TUN
/X 093266 TEX A 1
TÜV 1
IECEx
Ex tD A21 IP66 T100°C
CL.II, III, DIV.1, GP. EFG
II 2 D Ex tb IIIC T100 °C Db
CL.I, DIV.1, GP. ABCD
II 2 G Ex d IIC T6/T4 Gb
CL.I, ZN.1, AEx d IIC
-40
Ta +50(T6)/80(T4) °C
ZN.21, AEx tb IIIC T100°C Ta=85°C
IP66 / Type 4X
XP, CL.I, DIV.1, GP.CD
Ex d IIC
DIP, CL.II, DIV.1, GP.EFG, CL.III, DIV.1
Technical data and temperature classes see
certificate / operating instructions
SEAL ALL CONDUITS WITHIN 18 INCHES
13-KB4BO-0105
2006.1773456
S-XPL/090873






-40 Ta
+60°C(T6)/80°C(T4)
2001.1233781.
0518
① Approvals ③ FM/CSA marking for hazardous area
② ATEX/IECEx marking for hazardous area ④ Permitted ambient temperature for the hazardous
area of the corresponding temperature class
Figure1-2 Ex nameplate layout, example
1.7 Industrial use note
NOTICE
Use in a domestic environment
This Class A Group 1 equipment is intended for use in industrial areas.
In a domestic environment this device may cause radio interference.
1.8 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. 󹪝rewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Introduction
1.8Security information
SITRANS CC220 and SITRANS MS200
Compact Operating Instructions, 10/2023 - DRAFT, A5E...-AA 9