Sigma 8KBS - Manual Mode; Starting a Centrifugation Run; Interrupting a Centrifugation Run; Interrupting a Deceleration Process

Refrigerated Centrifuge Sigma 8KS
Refrigerated Centrifuge Sigma 8KBS
6 Using the centrifuge
46 / 131
Version 08/2012, Rev. 2.5 of 02/07/2018 • sb
Translation of the original operating manual, part no. 0702502
Pos: 146 /100 Sig ma/100 BA Ze ntrifugen Sig ma (Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol S (Z ent7)/060- 0030-0020 M anueller Betri eb @ 27\mod _1405320198028 _68.docx @ 193151 @ 3 @ 1

6.3.2 Manual mode
Pos: 147 /100 Sig ma/100 BA Ze ntrifugen Sig ma (Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol S (Z ent7)/060- 0030-0020-0 010 Starten ei ner Zentrifugati on @ 27\m od_140532019923 7_68.docx @ 193165 @ 4 @ 1

6.3.2.1 Starting a centrifugation run
The centrifuge is ready for operation when the start key is illuminated.
• Press the start key in order to start a centrifugation run.
Pos: 148 /010 Uni versalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 1 14 @ @ 1
Pos: 149 /100 Sig ma/100 BA Ze ntrifugen Sig ma (Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol S (Z ent7)/060- 0030-0020-0 020 Unterbr echen einer Zentr ifugation @ 27\mod_1405 320200374_68. docx @ 193179 @ 4 @ 1

6.3.2.2 Interrupting a centrifugation run
• Press the stop key in order to interrupt a centrifugation run. The
centrifugation run will be terminated prematurely.
Quick stop
• Press the stop key for more than three seconds.
The centrifuge decelerates with the maximum deceleration curve.
After a quick stop, the centrifuge lid must be opened before a new
centrifugation run can be started.
A quick stop can also be triggered during a normal deceleration, e.g. in
order to speed up the deceleration.
When a quick stop is triggered, ―Quick stop‖ will be displayed in the speed
field.
NOTE
A quick stop can be performed even if the centrifuge is blocked against
unauthorised use.
Pos: 150 /010 Uni versalmodule/ Leerz eile @ 0\mod_12 02116244500 _0.docx @ 1 14 @ @ 1
Pos: 151 /100 Sig ma/100 BA Ze ntrifugen Sig ma (Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol S (Z ent7)/060- 0030-0020-0 030 Unterbr echen eines Bre msvorgangs @ 2 7\mod_140 5320201742_68.d ocx @ 1931 93 @ 4 @ 1

6.3.2.3 Interrupting a deceleration process
• Press the start key during a deceleration process in order to interrupt it
and to restart the centrifuge.
Pos: 152 /010 Uni versalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 1 14 @ @ 1
Pos: 153 /100 Sig ma/100 BA Ze ntrifugen Sig ma (Standardmo dule)/060 Betrieb _Spincontrol L+S/Spincontrol S (Z ent7)/0 60-0030-0020-0 040 Auswahl, Anzeige und Änderung von Dat en @ 27\m od_14053202029 14_68.docx @ 193207 @ 4 @ 1

6.3.2.4 Selection, display, and modification of data
The "Standard" menu is displayed.
• Turn the function knob in order to select a field. The selected field is
inverted.
• Press the function knob. The display starts to flash and the modification
mode is active.
• Turn the function knob in order to modify the set value of the selected
field.
• Press the function knob again to confirm the entry and to quit the
modification mode.
Pos: 154 /010 Uni versalmodule/ Seitenwechsel @ 0\mod_12 02116244312 _0.docx @ 105 @ @ 1