Why is bottom tracking intermittent or erroneous on Skipper Boating Equipment?
Intermittent or erroneous bottom tracking can occur due to marginal gain or power settings, weather conditions, or a faulty transducer installation. Adjust the gain and power settings. Also, check the transducer wiring.
Why does my Skipper DL850 Marine Equipment status screen show Transmit/Receive (TX RX) Noise?
The 'Transmit/Receive (TX RX) Noise' message on the status screen could indicate that the cable is not connected to ground or the 0 Volt terminal. Check the cable screen to ensure it's properly grounded. It could also mean that one of the RECEIVEA/RECEIVEB wires on the display side or XMITA/XMITB on the transceiver side is not connected. Verify the connection of these data lines.
How to fix a malfunctioning display backlight on Skipper DL850?
If the display backlight is malfunctioning and the display picture is hardly visible, try the following: 1. Turn off the power and wait for 5 seconds before restarting the device, as this could be due to DL850 initialization issues. 2. The backlight tubes could be defective and need replacement. 3. The backlight inverter PCB might be defective, requiring replacement.
What to do if NMEA input signals are listed but not accepted by the DL850 Skipper Boating Equipment?
If NMEA input signals are listed but not accepted by the DL850, cycle the DL850 power or do a 'factory reset' after the NMEA connection is established. Also, check the remote (talker) setup.
What to do if the status screen shows Handshake (HSIN HSOUT) and the LEDs never turn on for Skipper Boating Equipment?
If the status screen shows 'Handshake (HSIN HSOUT)' and the LEDs on the power and transmitter PCBs never turn on, first switch on the power in the transceiver unit or check the fuses. Then, check the connection and polarity of the handshake lines. Finally, test or replace the communication cable.
What causes unrealistic aft speed values in docking mode on Skipper Boating Equipment?
Unrealistic aft speed values in docking mode are caused by a wrong setup of ship parameters. Check installation values for overall length and bow to sensor.
What to do if NMEA input signals are not listed in the NMEA input screen of my Skipper DL850?
If NMEA input signals are not listed in the NMEA input screen, it could be due to the wrong polarity of the input signals. Swap the NMEA input lines.
Why are there unrealistic aft speed values in docking mode on my Skipper DL850?
Unrealistic aft speed values in docking mode could be due to a wrong setup of ship parameters. Check the installation values for overall length and bow to sensor.
What to do if the status screen shows Transmit/Receive (TX RX) Noise on Skipper Boating Equipment?
If the status screen shows 'Transmit/Receive (TX RX) Noise', replace the receiver PCB.
What to do if panel buttons malfunction on Skipper Marine Equipment?
If the panel buttons are malfunctioning, it could be due to defective buttons or interface. Replace the keyboard PCB or I/O PCB. It could also be that one button is stuck. Check the key switch(es) or replace the keyboard PCB. Finally, it could be a software problem, so recycle power or do a 'factory reset'.
Definitions of units used for distance, speed, rotation, pulse indication, and temperature.
Symbols and abbreviations used on runtime and setup screens for various parameters.
Description of the DL850 Doppler speed log system, its capabilities, interfaces, and main components.
How to navigate between screens, use Day/Night mode, and adjust brightness.
Details on primary, setup screens, and procedures for entering system parameters.
Steps to enable advanced functions using the "hidden" button for system configuration.
Important warnings, handling precautions, and components included in the DL850 system supply.
Guidance on installing transducer, operator unit, transceiver, and selecting voltage settings.
Details on terminal PCB connections, NMEA interface, pulse outputs, and power failure relay.
Procedure to correct angular sensor installation error for accurate heading measurements.
Steps to enable calibration functions, which are disabled by default for safety.
Manual and semi-automatic methods for calibrating speed variations due to drag or mounting tilt.
Troubleshooting common problems like no display, backlight issues, and installation connection errors.
Diagnosing issues with NMEA signals, analogue/pulse outputs, and basic system functionality.
Interpreting status screen information and using diagnostic tests for fault finding.
Methods for recording sensor data and resetting system parameters to factory defaults.
Physical dimensions, mounting details, and technical specifications of the DL850 system.
Operational ranges, accuracy, limitations, and environmental operating conditions.
Guidelines for requesting service, including required information for support.
Collection of diagrams showing PCB layout, connections, and unit dimensions.
Procedures for upgrading software and configuring the CPU board.
Details on echo sounder, GPS:BT, current, beam filter, and NAUT rules functionalities.
General| Brand | Skipper |
|---|---|
| Model | DL850 |
| Category | Marine Equipment |
| Language | English |
To Next Page
