EasyManua.ls Logo

Skipper GDS101 - User Manual

Skipper GDS101
70 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Document no: DM-G001-SB
Rev: 1414A
For sw ver 05.05.16 - 5.05.17
Edition: 2014-04-01
SKIPPER Electronics AS Telephone: +47 23 30 22 70
Enebakkveien 150 Telefax: +47 23 30 22 71
P. O. Box 151, Manglerud E-mail: support@skipper.no
0612 Oslo, Norway Co. reg. no:NO-965378847-MVA
www.skipper.no
GDS101
Operation and Installation Manual
Graphic Depth Sounder

Table of Contents

Other manuals for Skipper GDS101

Preview: Quick Start Guide
Quick Start Guide2 pages
Preview: Replacement Procedure
Replacement Procedure14 pages

Questions and Answers

  • S
    Steven LeeAug 15, 2025
    Why is there no picture on my Skipper GDS101 Marine Equipment LCD screen?
    • R
      reillymonicaAug 15, 2025
      There might be several reasons why there is no picture on the LCD screen of your Skipper Marine Equipment: * There is no AC or DC power to the system. Check the switches and fuses on the terminal board inside the GDS101 cabinet. * The system is in standby. Press any button on the panel. * The screen backlight is too low. Increase the backlight setting or change to day vision. * The LCD module or interface is defective. Replace the module or backlight inverter PCB. * The voltage(s) are out of range. Replace the terminal PCB. * The system rebooted too quickly. Turn off the power switch(es), wait a few seconds, and then restart.
  • T
    Teresa WebbAug 18, 2025
    What to do if the picture on my Skipper GDS101 is difficult to read?
    • D
      dustin74Aug 18, 2025
      If the picture on your Skipper Marine Equipment is difficult to read, it could be due to the following reasons: * The backlight is too weak. Increase the backlight setting. * Night vision is on during the daytime. Increase the backlight setting or change to day vision.
  • L
    Lori BradleyAug 21, 2025
    Why are the panel buttons malfunctioning on my Skipper Marine Equipment?
    • A
      Andrea BrooksAug 21, 2025
      If the panel buttons on your Skipper Marine Equipment are malfunctioning, the cause may be: * Defective buttons or interface. Replace the keyboard PCB or terminal PCB. * One button is stuck. Check the key switches or replace the keyboard PCB.
  • K
    Kristin FowlerAug 25, 2025
    What to do if display backlight malfunctions on Skipper GDS101 Marine Equipment?
    • H
      Heather WilliamsAug 25, 2025
      If the display backlight malfunctions or the display picture is hardly visible on your Skipper Marine Equipment, consider the following: * Defective backlight tubes. Replace the tube assembly. * Defective keyboard. Replace the keyboard PCB. * Defective backlight inverter. Replace the backlight inverter PCB.
  • V
    veronica44Aug 27, 2025
    How to troubleshoot rotary encoder malfunctions in Skipper GDS101 Marine Equipment?
    • G
      garybryantAug 27, 2025
      If the rotary encoder on your Skipper Marine Equipment is malfunctioning: * The encoder or interface might be defective. Replace the keyboard PCB or terminal PCB. * There may be a cabling error. Check the cabling to the IO board J101 at both ends, ensuring there is no cable on J103.
  • H
    Heather TranAug 30, 2025
    How to fix no picture on Skipper Marine Equipment LCD screen?
    • S
      Samantha ChristensenAug 30, 2025
      If your Skipper Marine Equipment LCD screen shows no picture, first ensure the system is receiving AC or DC power by checking the switches and fuses on the terminal board inside the GDS101 cabinet. If powered, check if the system is in standby and, if so, press any button on the panel. Also, the screen backlight might be too low, so increase the backlight setting or switch to day vision. If these steps don't resolve the issue, there may be a defective LCD module or interface, requiring replacement of the module or backlight inverter PCB. Voltage issues could also be the cause, in which case the terminal PCB should be replaced. Finally, if the system rebooted too quickly, turn off the power switch(es), wait a few seconds, and then restart.
  • R
    Ronald MooreSep 2, 2025
    Why is the picture difficult to read on my Skipper Marine Equipment?
    • L
      Lee MonroeSep 2, 2025
      If the picture on your Skipper Marine Equipment is difficult to read, it might be due to a weak backlight. Try increasing the backlight setting. Also, ensure that night vision is not enabled during the daytime. If it is, either increase the backlight setting or switch to day vision.
  • T
    Tracy SmithSep 5, 2025
    What to do if panel buttons malfunction on Skipper Marine Equipment?
    • J
      Jeffrey SanchezSep 5, 2025
      If the panel buttons on your Skipper Marine Equipment are malfunctioning, it could be due to defective buttons or interface. In this case, replace the keyboard PCB or terminal PCB. Another potential cause is a stuck button. Inspect the key switches and replace the keyboard PCB if necessary.
  • N
    Nicole HernandezSep 8, 2025
    How to troubleshoot display backlight malfunctions on Skipper Marine Equipment?
    • C
      crystal89Sep 8, 2025
      If the display backlight on your Skipper Marine Equipment malfunctions, causing the display picture to be hardly visible, the issue might stem from defective backlight tubes. Try replacing the tube assembly. Alternatively, the keyboard or backlight inverter could be defective, requiring replacement of the keyboard PCB or backlight inverter PCB, respectively.
  • A
    Amy StevensonSep 12, 2025
    Why is the rotary encoder malfunctioning on my Skipper Marine Equipment?
    • B
      barnestrevorSep 12, 2025
      If the rotary encoder on your Skipper Marine Equipment is malfunctioning, the cause could be a defective encoder or interface. Try replacing the keyboard PCB or terminal PCB. Another possibility is a cabling error. Check the cabling to the IO board J101 at both ends, ensuring there is no cable on J103.

Summary

Introduction

System Summary

Overview of the echo sounder system's capabilities and design.

Transducers

Information on compatible transducer frequencies and connection options.

Operator Panel and Data Entry

Description of the graphic LCD, keyboard, and input methods.

Recorded Data Storage

Details on the 24-hour history memory and printing capabilities.

Interfacing

Overview of the GDS101's interface possibilities for external devices.

Options

Description of optional features like repeaters and remote control.

Operation

Parameter Entry

Procedure for changing settings and entering data using keys and encoder.

Operation Screens

How to select and navigate through the system's various screens.

Primary Operation Screens

Detailed layout and functions of the main echo gram display screens.

Secondary Operation Screens

Layout and functions of setup, calendar, language, and interface screens.

Principal Functions

Core functionalities including bottom detection, filtering, and power control.

Fixed Key Functions

Explanation of the purpose and operation of dedicated buttons.

Soft Key Functions

Description of context-sensitive functions available via soft keys.

User Maintenance

Transducer Maintenance

Guidance on occasional cleaning and care for transducers.

Operator Unit Maintenance

Instructions for cleaning the front panel of the operator unit.

Trouble Shooting

Common symptoms, causes, and remedies for system issues.

Installation

Standard System Supply

Components of a basic GDS101 system and installation overview.

Transducer Installation

Guidelines for optimal transducer location and mounting procedures.

Operator Unit Installation

Instructions for mounting the operator unit, including panel cut-out dimensions.

115;230 V Selection

Procedure for configuring the AC power supply voltage.

EMC

Important notes on meeting Electromagnetic Compatibility requirements.

Interfacing

Details on connecting external devices like alarm systems and logs.

Start-up and System Adaption

System Adaptation

Configuring output ranges, language, and units of measure.

NMEA Setup

Configuration of NMEA communication channels and transmitted messages.

Specifications, Dimensions

Transducer Specifications

Technical details including diameter, mounting, cable length, and protection.

Operator Unit Cabinet Specifications

Physical dimensions, weight, and protection rating of the unit.

Functional Properties

Summary of display, printer, and interface capabilities.

Performance

Key performance metrics like depth range, resolution, and transducer power.

Environmental Specifications

Operating temperature, storage, humidity, and protection ratings.

Service

Service and Repair Information

Guidelines for requesting service and authorized repairs.

CPU Board Setup Procedure

CPU PCA 6742 VE

Steps for configuring BIOS, chipset, and peripherals on the CPU board.

Master Reset Procedure

Procedure to reset the GDS101 to factory default settings.

Upgrading Software

Step-by-step guide for updating the system software via Compact Flash.

Appendix, Miscellaneous Drawings

Miscellaneous Diagrams

References to various technical drawings and installation manuals.

Warranty and Utilization

Warranty Information

Details on the product guarantee period and how to make a warranty request.

Utilization and Disposal

Guidelines for proper equipment use and disposal according to regulations.

Notes

Notes Section

A section for user-specific remarks or observations.

Skipper GDS101 Specifications

General IconGeneral
GPSNo
Waterproof RatingIPX7
Operating Temperature-15°C to 55°C
Frequency200 kHz
WaypointsNo
TracksNo
TypeEcho Sounder/Fish Finder

Related product manuals