Space ER232R - Table of Contents

GB
Page 2 of 58
INSTRUCTION, USE AND
MAINTENANCE MANUAL
1296-M010-0_P
Space s.r.l.
ER232R - ER234R - ER236R - ER238R - ER238RFM - ER248R - ERP248R
SUMMARY
SYMBOLS USED IN THE MANUAL AND ON
THE MACHINE __________________________ 6
1.0 GENERAL INTRODUCTION _________ 8
1.1 Introduction ___________________________8
2.0 INTENDED USE ____________________ 8
2.1 Training of personnel__________________8
3.0 SAFETY DEVICES __________________ 9
3.1 Residual risks _________________________9
4.0 GENERAL SAFETY RULES _________ 9
5.0 PACKING AND MOBILIZATION FOR
TRANSPORT ______________________ 10
6.0 UNPACKING _______________________ 11
7.0 MOBILIZATION ____________________ 11
8.0 WORKING ENVIRONMENT
CONDITIONS ______________________ 11
8.1 Working area ________________________ 12
8.2 Lighting _____________________________ 12
9.0 MACHINE ASSEMBLY _____________ 13
9.1 Anchoring system ___________________ 13
9.2 Accessories contained in the packing _ 13
9.3 Assembly procedure _________________ 14
9.3.1 Fitting the shaft on the flange ___ 14
9.3.2 Fitting and removal of the
pneumatic mandrel on the
flange ___________________________ 15
9.3.3 Fitting the protection guard _____ 16
9.3.4 Fitting of GAR301 automatic
external data gauge(optional for
ER236R - ER238R - ER238RFM) _ 17
9.3.5 Fitting of GAR266 automatic
external data gauge (optional for
ER248R - ERP248R) _____________ 18
9.3.6 Fitting of GAR264 automatic
external data gauge (optional for
ER248R - ERP248R) _____________ 19
10.0 ELECTRICAL CONNECTION _______ 20
10.1 Electrical checks ____________________ 20
11.0 AIR CONNECTION _________________ 21
12.0 FITTING THE WHEEL ON THE
MANDREL _________________________ 21
12.1 Wheel assembly _____________________ 21
12.2 Wheel assembly _____________________ 23
13.0 DISPLAY WITH KEYBOARD _______ 24
13.1 Brightness and contrast adjustment _ 25
14.0 SWITCHING THE MACHINE ON
AND OFF __________________________ 25
15.0 WHEEL BALANCING ______________ 26
15.1 Determination of wheel dimensions _ 26
15.1.1 Manual setting of wheel
dimensions for dynamic static
and balancing functions ________ 26
15.1.2 Wheel dimension manual setting
for ALU-S type correction and
auxiliary programs _____________ 29
15.2 User management ___________________ 30
15.3 Unbalance measurement ____________ 30
15.3.1 Dynamic balancing ______________ 30
15.3.2 Wheel positioning _______________ 31
15.3.3 Static balancing (STAT) _________ 32
15.4 Measuring the unbalance with
auxiliary programs _________________ 33
15.4.1 ALU-S ___________________________ 33
15.4.2 STATIC __________________________ 33
15.4.3 ALU-S1 __________________________ 33
15.4.4 ALU-S2 __________________________ 34
15.4.5 STATIC 1 ________________________ 34
15.4.6 STATIC 2 ________________________ 34
15.4.7 ALU 1 ____________________________ 34
15.4.8 ALU 2 ____________________________ 34
15.4.9 ALU 3 ____________________________ 35
15.4.10 ALU 4 __________________________ 35
15.4.11 PAX_____________________________ 35
15.4.12 ALU-S procedure _______________ 35
15.4.13 ALU 1 procedure _______________ 36
15.4.14 PAX mode ______________________ 38
15.5 Recalculation Function ______________ 38
16.0 WHEEL BALANCING IN
MOTORBIKE MODE _______________ 39
17.0 SPLIT PROCEDURE _______________ 40
18.0 WEIGHTS HIDDEN BEHIND
SPOKES MODE ____________________ 42
19.0 MATCHING PROCEDURE
(Rim - Tyre Optimisation)
__________ 44
20.0 SETUP OF UNITS OF WEIGHT
MEASUREMENT AND RIM WIDTH/
DIAMETER AND SETTING CAR/
MOTORCYCLE MODE
_____________ 46
20.1 Width measurement options setting _ 48
20.2 Lower weight limit __________________ 48