Home
Supero
Controller
SMT IPMI
Supero SMT IPMI User Manual
4
of 1
of 1 rating
109 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
2-54
SMT IPMI User's Guide
2.9.1.5.9
Console
Redirection
-
Keyboard/Mouse
Hotplug
1.
Click <Options> on the menu bar to invoke the pull-down submenu.
2.
Click <Keyboard/Mouse Hotplug> from the pull-down menu to enable key
-
board/mouse hotplug support for your console redirection.
2
1
65
67
Table of Contents
Preface
3
Contacting Supermicro
4
Table of Contents
6
Chapter 1 Introduction
9
Overview of the Nuvoton WPCM450 BMC Controller
9
WPCM450 DDR2 Memory Interface
9
WPCM450 PCI System Interface
9
Supermicro IPMI Features
10
WPCM450 Block Diagram
11
Introduction to the IPMI Platform
11
Motherboards Supported
12
An Important Note to the User
12
Chapter 2 Configuring the IPMI Settings
13
Configuring BIOS
13
Configuring the IP/MAC Addresses for Remote Servers
16
Connecting to the Remote Server
18
Using the Ipmiview to Connect to the Remote Server
18
Using the Browser to Connect to the Remote Server
18
Accessing the Remote Server Via Console Redirection Using the Browser
19
To Log in to the Remote Console
19
IPMI Main Screen
20
System Status
21
Server Health
22
Sensor Readings
23
Event Log
25
Configuration
27
Configuring the Alerts Settings
28
Configuring Date and Time Settings
31
Configuring Light-Weight Directory Access Protocol (LDAP) Settings
32
Active Directory Settings
33
Configuring the Radius Settings
35
Configuring the Mouse Mode Settings
36
Configuring Network Settings
37
Configuring Dynamic DNS (Domain Name System) Settings
39
Configuring the Remote Session Settings
40
Configuring the SMTP Settings
41
Configuring the SSL (Secure Sockets Layer) Certification
42
Configuring Users Settings
43
Configuring Port Settings
44
IP Access Control
45
Configuring Fan Settings
47
Remote Control
48
Launching Console Redirection
49
Remote Control - Server Power Control
70
Remote Control-Launch SOL
71
Virtual Media
73
Configuring USB Floppy & Flash Device Settings
74
Configuring CD ROM Image File Settings
75
Maintenance
77
Maintenance - Firmware Update
78
Maintenance - Unit Reset
80
Maintenance - IKVM Reset
81
Maintenance - Factory Default
82
Maintenance - IPMI Configuration
83
Miscellaneous
84
Miscellaneous - POST Snooping
84
Miscellaneous - UID Control
85
Chapter 3 Frequently Asked Questions
87
Frequently Asked Questions
87
A-1 Overview
89
Appendix A Flash Tools
89
Overview
89
Reference
89
A-2 Reference
89
A-3 Using Aten Flash Tools in the DOS Environment
89
Using Aten Flash Tools in the DOS Environment
89
Firmware Updating Via KCS Channels
90
Dumping Firmware from the BMC Via KCS Channels
91
Windows/Linux Version of Flash Tools
92
Appendix B Introduction to SMASH
95
Overview
95
B-1 Overview
95
How SMASH Works
95
SMASH Compliance Information
96
An Important Note to the User
96
Using SMASH
97
Initiating the SMASH Protocol
97
To Initiate SMASH Automatically
97
SMASH-CLP Main Screen
98
Using SMASH for System Management
98
Definitions of Command Verbs
99
SMASH Commands
101
Standard Command Options
102
Target Addressing
103
Terms Used in the Target Addressing Diagram
103
Appendix C RADIUS Setup Guidelines
105
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Supero SMT IPMI and is the answer not in the manual?
Ask a question
Supero SMT IPMI Specifications
General
Brand
Supero
Model
SMT IPMI
Category
Controller
Language
English
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General