Technogym Step 600 XTPRO - Page 6

STEP 600 XTPRO: Service & Maintenance Manual - rev. 1.1
Page ii
7.3. DISASSEMBLING THE CPU BOARD......................................................................................................................7.4
7.4. DISASSEMBLING THE KEYBOARD ......................................................................................................................7.5
7.5. DISASSEMBLING THE CARDIO RECEIVER............................................................................................................7.6
7.6. DISASSEMBLING THE UPRIGHT GUARD ..............................................................................................................7.7
7.7. DISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS .........................................................................................7.8
7.8. DISASSEMBLING THE FRAME GUARD .................................................................................................................7.9
7.9. DISASSEMBLING THE CENTER HANDLEBAR .....................................................................................................7.10
7.10. DISASSEMBLING THE SIDE HANDLEBARS .........................................................................................................7.11
7.11. DISASSEMBLING THE HS INTERFACE BOARD ....................................................................................................7.12
7.12. DISASSEMBLING THE HAND SENSORS ..............................................................................................................7.13
7.13. DISASSEMBLING THE PEDAL SPRING - CHAIN...................................................................................................7.14
7.14. DISASSEMBLING THE PEDAL JOINT ..................................................................................................................7.15
7.15. DISASSEMBLING THE PEDALS AND THE PEDAL GROUP .....................................................................................7.16
7.16. DISASSEMBLING THE PEDAL CONNECTING RODS .............................................................................................7.18
7.17. DISASSEMBLING THE LEVERS ..........................................................................................................................7.19
7.18. DISASSEMBLING THE LEVER FRAME ................................................................................................................7.20
7.19. DISASSEMBLING THE PRIMARY SHAFT - SECONDARY SHAFT CHAIN.................................................................7.21
7.20. DISASSEMBLING THE PRIMARY SHAFT.............................................................................................................7.22
7.21. DISASSEMBLING THE SECONDARY SHAFT........................................................................................................7.23
7.22. DISASSEMBLING THE PULLEYS ........................................................................................................................7.25
7.23. DISASSEMBLING THE BELT ..............................................................................................................................7.26
7.24. DISASSEMBLING THE ALTERNATOR .................................................................................................................7.28
7.25. DISASSEMBLING THE ALTERNATOR BRUSHES ..................................................................................................7.29
8. ADJUSTMENTS ....................................................................................................................................................8.1
8.1. BELT ALIGNMENT..............................................................................................................................................8.1
8.2. BELT TENSION...................................................................................................................................................8.2
8.3. ALIGNMENT OF PRIMARY SHAFT - SECONDARY SHAFT CHAIN............................................................................8.3
8.4. TENSION OF PRIMARY SHAFT - SECONDARY SHAFT CHAIN.................................................................................8.4
8.5. WEAR OF ALTERNATOR BRUSHES......................................................................................................................8.5
9. CONFIGURING THE MACHINE.......................................................................................................................9.1
9.1. USER SETTING PARAMETERS .............................................................................................................................9.1
9.1.1. Language used...................................................................................................................................9.1
9.1.2. Measurement system..........................................................................................................................9.1
9.1.3. Maximum time ...................................................................................................................................9.2
9.1.4. Activating the “+” and “ − ” keys ......................................................................................................9.2
9.1.5. Disabling the function keys ...............................................................................................................9.2
9.1.6. Enabling the “ENTER” key...............................................................................................................9.3
9.1.7. Setting the priority.............................................................................................................................9.3
9.2. TECHNICAL SETTING PARAMETERS ...................................................................................................................9.3
9.2.1. Enabling use of the hand sensor........................................................................................................9.3
9.2.2. Enabling the display mode ................................................................................................................9.4
9.3. MAINTENANCE INFORMATION...........................................................................................................................9.4
9.3.1. Hours on............................................................................................................................................9.4
9.3.2. Hours of use.......................................................................................................................................9.4
9.4. CHANGING THE MAINTENANCE INFORMATION...................................................................................................9.5
9.4.1. Hours on............................................................................................................................................9.5
9.4.2. Hours of use.......................................................................................................................................9.5
10. SCHEDULED MAINTENANCE........................................................................................................................10.1
10.1. EXTERNAL CLEANING OPERATIONS .................................................................................................................10.1
10.1.1. Setting up the operation...................................................................................................................10.1
10.1.2. Cleaning operations.........................................................................................................................10.1
10.2. ROUTINE MAINTENANCE OPERATIONS.............................................................................................................10.2
10.2.1. Setting up the operation...................................................................................................................10.2
10.2.2. Internal cleaning..............................................................................................................................10.2
10.2.3. Lubrication ......................................................................................................................................10.2