Triple E COMMANDER Series - Page 29

4-7
4.7 TV INPUT SELECTOR AND
DVD/VCR COMBO (optional)
Certain pieces of entertainment equipment are
installed inside the front upper cabinets above the
dashboard for convenience and looks.
A. Input Selector:
An input channel selector is located on top of the
DVD/VCR and is used to select a specic signal to
each TV in the vehicle or the VCR.
TV1
a. ANT:
This push button switch selects the
external antenna as the source of the input
signal to TV 1 or the one mounted in the
front console.
b. AUX:
This push button switch selects the
auxiliary signal, normally cable, as the
source of the input signal to TV 1 or the
one mounted in the front console.
c. VCR:
This push button switch selects the VCR
output as the source of the input signal
to TV 1 or the one mounted in the front
console.
VCR
a. ANT:
This push button switch selects the
antenna signal and directs it into the VCR.
b. AUX:
This push button switch selects the
auxiliary signal, normally the external cable
input, and directs it into the VCR.
TV2 a. ANT:
This push button switch selects the
external antenna as the source of the input
signal to TV 2 or the one mounted in the
bedroom.
b. AUX:
This push button switch selects the
auxiliary signal, normally cable, as
the source of the input cable to TV-2
(bedroom).
c. VCR:
COMMANDER / EMBASSY
Fig. 4-11 TV INPUT SELECTOR AND DVD/VCR
A
B
C
This push button switch
B. DVD/VCR:
Refer to the instructions in the Owner's information
package for details. Close the cabinet door when
DVD/VCR access is not required.
C. TV Antenna Signal Booster:
Depress the push button switch to activate the
antenna signal booster for better TV reception.
Depress it again to turn it off.
4-7
4.7 TV INPUT SELECTOR AND
DVD/VCR COMBO (optional)
Certain pieces of entertainment equipment are
installed inside the front upper cabinets above the
dashboard for convenience and looks.
A. Input Selector:
An input channel selector is located on top of the
DVD/VCR and is used to select a specic signal to
each TV in the vehicle or the VCR.
TV1
a. ANT:
This push button switch selects the
external antenna as the source of the input
signal to TV 1 or the one mounted in the
front console.
b. AUX:
This push button switch selects the
auxiliary signal, normally cable, as the
source of the input signal to TV 1 or the
one mounted in the front console.
c. VCR:
This push button switch selects the VCR
output as the source of the input signal
to TV 1 or the one mounted in the front
console.
VCR
a. ANT:
This push button switch selects the
antenna signal and directs it into the VCR.
b. AUX:
This push button switch selects the
auxiliary signal, normally the external cable
input, and directs it into the VCR.
TV2 a. ANT:
This push button switch selects the
external antenna as the source of the input
signal to TV 2 or the one mounted in the
bedroom.
b. AUX:
This push button switch selects the
auxiliary signal, normally cable, as
the source of the input cable to TV-2
(bedroom).
c. VCR:
COMMANDER / EMBASSY
Fig. 4-11 TV INPUT SELECTOR AND DVD/VCR
A
B
C
This push button switch
B. DVD/VCR:
Refer to the instructions in the Owner's information
package for details. Close the cabinet door when
DVD/VCR access is not required.
C. TV Antenna Signal Booster:
Depress the push button switch to activate the
antenna signal booster for better TV reception.
Depress it again to turn it off.