What does 'RTC Error - Please Set Current Date and Time' mean on Tuttnauer Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays a 'RTC Error - Please Set Current Date and Time' message, it indicates that the date and time need to be set. Set the current date and time. If the problem persists, it is recommended to call the technician.
What does 'Pressure Time Error' mean on Tuttnauer 3840 Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays a 'Pressure Time Error' message, it means the system cannot reach the required pressure conditions in the chamber, after preset time, during the air removal stage. Verify that the autoclave is not overloaded.
What does 'Heat Time Error (Keep)' mean on Tuttnauer 3840?
If the Tuttnauer Laboratory Equipment displays a 'Heat Time Error (Keep)' message, it indicates that the system cannot reach the required temperature in the chamber during the optional "Keep Heat" stage within the preset time. To address this, verify that the autoclave is not overloaded.
What to do if Tuttnauer 3840 Laboratory Equipment displays a 'High Temp' error?
If your Tuttnauer Laboratory Equipment displays a 'High Temp' error, first, try performing a new cycle. If the problem continues, the door gasket might be leaking, and you should replace it.
How to fix a Tuttnauer 3840 Laboratory Equipment machine that is not responding?
If the Tuttnauer Laboratory Equipment machine isn't responding, first, ensure the main switch is in the ‘On’ position. Then, verify the power cord is properly connected to both the machine and the mains. Finally, check the circuit breaker and lift the lever if it has tripped. These issues may be caused by the main switch being off, the power cord being disconnected, or a tripped circuit breaker.
Why is the Tuttnauer Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, it could be due to a dirty or damaged door gasket. Clean the door gasket first. If the leak persists, replace the door gasket.
What does 'Low Pressure' mean on Tuttnauer 3840 Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays a 'Low Pressure' message, it indicates that the chamber pressure dropped below the sterilization pressure (134°C = 304 kPa, 121°C = 205 kPa) for 2 seconds during the sterilization stage. To resolve this, perform a new cycle.
What does 'High Pressure' mean on Tuttnauer 3840?
If the Tuttnauer Laboratory Equipment displays a 'High Pressure' message, it means the chamber pressure rose 4.2 psi-29 kPa above the sterilization pressure (134°C = 304 kPa, 121°C = 205 kPa) for 2 seconds during the sterilization stage. To address this, perform a new cycle.
What does 'High Temp. (Ending)' mean on Tuttnauer 3840 Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays a 'High Temp. (Ending)' message, it means the system could not reach the required temperature in the chamber within 10 minutes. To resolve this, perform a new cycle.
What does 'Low Temp' mean on Tuttnauer Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays a 'Low Temp' message, it indicates that the temperature dropped below the sterilization temperature for more than 1 second during the sterilization cycle. To address this, perform a new cycle.
Key safety guidelines for operating the autoclave.
Specific safety instructions for loading, operation, and unloading.
Physical dimensions and chamber specifications for models.
List of built-in safety features of the autoclave.
Identification of parts on the front view diagram.
Identification of parts on the front view diagram.
Identification of display, keypad, and printer on the panel.
Overview of the control panel sections.
Details of the LCD panel display and its information.
Functions of the UP, DOWN, and START/STOP keys.
Categorization of failures and references for error details.
Table of operational messages and required actions.
Parameters and description for the Glass sterilization program.
Parameters and description for the Plastic sterilization program.
Parameters and description for the Liquid A program.
Parameters and description for the Liquid B - Waste program.
Parameters and description for the Liquid A - Cooling program.
Parameters for the Bio Hazard Liquid Cooling program.
Parameters for the Bio Hazard Liquid program.
Parameters for the Bio Hazard 1 program.
Detailed description of the Glass program operations.
Detailed description of the Plastic program operations.
Detailed description of the Liquid A program operations.
Detailed description of the Liquid B - Waste program operations.
Detailed description of the Liquid A - Cooling program operations.
Detailed description of the Bio Hazard Liquid Cooling program.
Detailed description of the Bio Hazard Liquid program.
Detailed description of the Bio Hazard 1 program.
Displays for cycles aborted after the sterilization phase.
Display for cycles canceled by user post-sterilization.
Display for failures related to pressure/time post-sterilization.
Displays when a cycle fails, indicated by yellow screen.
Display for failure due to Pressure Time Error.
Display for failure due to user cancellation before sterilization.
Steps for preparing items for sterilization.
Preparation guidelines for instruments.
General safety precautions during operation.
Guidelines for properly loading the autoclave chamber.
Steps for selecting and verifying programs.
Procedure for initiating a sterilization cycle.
Steps for safely unloading the autoclave.
Detailed procedures for unloading the autoclave.
Routine operations to maintain the device.
General| Brand | Tuttnauer |
|---|---|
| Model | 3840 |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
