Vacon 100 - Page 111

To Next Page

To Previous Page

MR6

200-500 V

MR6

600/690 V

4 To disconnect the RFI filters from ground, remove

the EMC jumpers. Pull the EMC jumper out with the

tool.

COMMISSIONING AND ADDITIONAL INSTRUCTIONS VACON · 111

24-HOUR SUPPORT +358 (0)201 212 575 · EMAIL: VACON@VACON.COM

Main Page

About this Manual3
Table of Contents5
Approvals8
Safety10
The Safety Symbols Used in the Manual10
Warning10
Caution11
Grounding and Earth Fault Protection12
Electro-Magnetic Compatibility (EMC)13
Using an RCD or an RCM Device13
Receiving the Delivery15
Package Label15
Type Designation Code16
Contents of the Delivery16
Removing the Packaging and Lifting the AC Drive16
Weight of the AC Drive16
Lifting the Frames MR8 and MR917
Accessories18
Frame MR419
Frame MR519
Frame MR620
Frame MR721
Frame MR821
Frame MR922
Product Modified" Label22
Disposal22
Mounting23
General Information about Mounting23
Dimensions for Wall Mounting23
Wall Mounting of MR423
Wall Mounting of MR524
Wall Mounting of MR625
Wall Mounting of MR726
Wall Mounting of MR8, IP21 and IP5427
Wall Mounting of MR8, IP0028
Wall Mounting of MR9, IP21 and IP5429
Wall Mounting of MR9, IP0030
Dimensions for Wall Mounting, North America31
Wall Mounting of MR4, North America31
Wall Mounting of MR5, North America32
Wall Mounting of MR6, North America33
Wall Mounting of MR7, North America34
Wall Mounting of MR8, North America35
Wall Mounting of MR8, UL Open Type, North America36
Wall Mounting of MR9, North America37
Wall Mounting of MR9, UL Open Type, North America38
Dimensions for Flange Mounting38
Flange Mounting of MR442
Flange Mounting of MR543
Flange Mounting of MR644
Flange Mounting of MR745
Flange Mounting of MR846
Flange Mounting of MR947
Dimensions for Flange Mounting, North America48
Flange Mounting of MR4, North America48
Flange Mounting of MR5, North America49
Flange Mounting of MR6, North America50
Flange Mounting of MR7, North America51
Flange Mounting of MR8, North America52
Flange Mounting of MR9, North America53
Cooling54
Power Cabling57
Cable Connections57
UL Standards on Cabling58
Cable Dimensioning and Selection58
Cable and Fuse Sizes58
Cable and Fuse Sizes, North America63
Brake Resistor Cables68
Preparing for the Cable Installation69
Cable Installation69
Frames MR4 to MR769
Frames MR8 to MR976
Installation in a Corner-Grounded Network88
Control Unit89
Control Unit Components89
Control Unit Cabling90
Selection of the Control Cables90
Control Terminals and DIP Switches91
Fieldbus Connection95
Using Fieldbus through an Ethernet Cable96
Using Fieldbus through an RS485 Cable99
Installation of Option Boards103
The Installation Procedure104
Installation of a Battery for the Real Time Clock (RTC)105
Galvanic Isolation Barriers105
Commissioning and Additional Instructions107
Commissioning Safety107
Commissioning of the Drive107
Operation of the Motor108
Checks before Starting the Motor108
Measuring the Cable and Motor Insulation108
Installation in a Marine Environment109
Installation in an IT System109
The EMC Jumper in MR4, MR5 and MR6109
The EMC Jumper in MR7112
The EMC Jumper in MR8114
The EMC Jumper in MR9115
Maintenance116
Technical Data, Vacon118
AC Drive Power Ratings118
Mains Voltage 208-240 V118
Mains Voltage 380-500 V120
Mains Voltage 525-600 V121
Mains Voltage 525-690 V122
Overload Capability122
Brake Resistor Ratings123
Vacon ® 100 - Technical Data128
Technical Data, Vacon® 100 Flow133
AC Drive Power Ratings133
Mains Voltage 208-240 V133
Mains Voltage 380-500 V135
Mains Voltage 525-600 V136
Mains Voltage 525-690 V137
Overload Capability137
Vacon ® 100 FLOW - Technical Data139
Technical Data, Vacon® 100 HVAC144
AC Drive Power Ratings144
Mains Voltage 208-240 V144
Mains Voltage 380-500 V145
Overload Capability146
Vacon ® 100 HVAC - Technical Data147
Technical Data on Control Connections152

Vacon 100 - Page 111

Table of Contents

Other manuals for Vacon 100

Related product manuals