EasyManua.ls Logo

Wacker Neuson LTN 6L - User Manual

Wacker Neuson LTN 6L
118 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
0171883en 007 1110
0171883EN
Operator’s Manual
Light Tower
LTN 6L
60 Hz

Table of Contents

Questions and Answers

  • E
    esanchezAug 12, 2025
    Why is the light output low on my Wacker Neuson LTN 6L?
    • R
      Rebecca LarsonAug 12, 2025
      If your Wacker Neuson Lighting Equipment has low light output, the lamp may be degraded and need replacement due to normal lamp life. Another potential cause is low ballast output, so check the ballast for proper voltage output. Additionally, a dirty fixture or lens can reduce light, so clean the reflective surface inside the fixture and both the inside and outside surfaces of the glass lens.
  • C
    Chad BerryAug 22, 2025
    How to fix a loose plug connection on Wacker Neuson LTN 6L?
    • S
      sabrina98Aug 22, 2025
      If the plug connection at the fixture of your Wacker Neuson Lighting Equipment is loose or damaged, have a licensed electrician repair or replace it. Similarly, if the circuit breaker is loose or defective, a licensed electrician should repair or replace it.
  • L
    Larry JamesNov 1, 2025
    What to do if the lamp will not light on my Wacker Neuson Lighting Equipment?
    • R
      richard94Nov 1, 2025
      If the Wacker Neuson Lighting Equipment lamp won't light, several factors could be at play. First, the lamp may be too hot; allow it to cool for 10–15 minutes before attempting to restart it. Check for a faulty lamp connection by ensuring the lamp is securely tightened in its socket and inspecting connections inside the connection boxes on the light fixtures and tower. Also, inspect the lamp for a broken arc tube, outer lamp jacket, broken or loose components, or blackening/deposits inside the lamp tube. The circuit breaker may be turned on, so turn it off. The generator output might be incorrect; the incoming voltage to the ballast should be 120V ± 5V. If it's off, the engine speed may need adjustment, or the generator may require servicing. Finally, if the fixture cord is removed from it...

Summary

Foreword

Machine Documentation

Keep a copy of the Operator’s Manual with the machine at all times.

Manual Information Expectations

This manual provides information and procedures to safely operate and maintain.

California Proposition 65 Warning

Engine exhaust and components may contain chemicals known to cause cancer.

Manufacturers Approval

Manual references approved parts, attachments, and modifications.

Safety Information

Signal Words Used in this Manual

Explains DANGER, WARNING, CAUTION, NOTICE, and NOTE signal words for safety.

Machine Description and Intended Use

Details the mobile, trailer-mounted light tower and its intended purpose.

Operating Safety Guidelines

Familiarity and training are required for safe operation of the machine.

Operator Safety with Internal Combustion Engines

Hazards during operation and fueling of internal combustion engines.

Lamp Safety

Information regarding the electric discharge lamps and their safe operation.

Service Safety

High voltage warnings and safety precautions for servicing the equipment.

Labels

Label Locations

Diagrams showing the placement of various labels on the machine.

Label Meanings

Explanation of international pictorial labels used on Wacker Neuson machines.

Lifting the Machine

Lifting Procedure

Steps to check and prepare the machine for lifting.

Operation

Locating Trailer

Positioning the Light Tower for maximum light coverage and stability.

Leveling Trailer

Procedures for leveling the trailer and extending outriggers for stability.

Adjusting Lights

How to aim each light fixture up, down, left, or right.

Raising Tower (Manual Winch System)

Step-by-step guide for raising the tower using the manual winch.

Lowering Tower (Manual Winch System)

Step-by-step guide for lowering the tower using the manual winch.

Starting the Engine

Procedures for checking levels and starting the engine.

Stopping the Machine

Steps for safely shutting down the machine and its lights.

Factory Installed Options

Block Heater

Function of the engine block heater for cold-weather starting.

Battery Blanket

Warms the battery when the machine is not in use.

Oil Pan Heater

Warms engine oil for easier starting in cold temperatures.

Maintenance

Periodic Maintenance Schedule

Table of maintenance tasks and their recommended intervals.

Installing;Removing Light Fixtures

Procedure for disconnecting and removing light fixtures.

Replacing Lamps

Prerequisites and steps for removing and installing lamps.

Daily Inspection

Checks for fluid leaks, cord condition, cables, and locking pin.

Troubleshooting

Guide for diagnosing and resolving common lamp and output issues.

Technical Data

Engine Specifications

Details on engine power rating, speed, and capacities.

Generator Specifications

Generator output, frequency, power factor, and voltage regulation.

Machine Specifications

Weight, dimensions, lighting system, and tire size.

Schematics

Electrical Schematic

Diagram illustrating the overall electrical connections of the machine.

Trailer Wiring

Wiring diagram for the trailer's stop, turn, and tail lights.

Engine Wiring

Wiring diagram specific to the Lombardini engine components.

Control Panel Wiring

Diagram showing wiring connections for the control panel.

Power Winch Schematic

Diagram outlining the electrical connections for the power winch.

Appendix I-Assembly Instructions

Introduction

Manual contains assembly procedures for Wacker Neuson Light Towers.

Appendix II-Assembly Safety

Signal Words in Manual

Explanation of DANGER, WARNING, CAUTION, NOTICE, and NOTE signals.

Lifting Safety Guidelines

Guidelines for safely lifting or supporting the machine.

Pre-Assembly Checklist

Precautions and checks before beginning the assembly process.

Appendix III-Standard Pallet Assembly

Installing Outriggers and Jacks

Procedure to install the two outriggers and outrigger jacks.

Installing the Rear Jack

Procedure for installing the rear jack.

Installing the Tongue Assembly

Installation of tongue, jack, and trailer wiring.

Installing Upper Light Fixtures

Procedure for mounting the two upper light fixtures on the light tube.

Appendix IV-CE Pallet Assembly

Installing Side Jacks

Procedure to attach the two side jacks to the outriggers.

Installing the Rear Jack

Procedure for installing the rear jack.

Conclusion

Assembly procedure complete. Refer to Operator's Manual.

Appendix V-Standard Racked Assembly

Installing the Axle

Procedure to install the axle onto the trailer.

Installing the Fenders

Procedure to install the two fenders onto the Light Tower.

Installing the Wheels

Procedure to install the two wheels onto the axle.

Installing Outriggers and Jacks

Procedure to install the two outriggers and outrigger jacks.

Installing the Tower Lock Bracket

Procedure to install the tower lock bracket on the tower.

Installing the Tower Cradle

Procedure to assemble the tower cradle.

Installing the Tower

Procedure to install the tower assembly onto the Light Tower enclosure.

Wiring the Junction Box

Procedure to connect the wiring at the junction box.

Routing the Coil Cord

Procedure for routing the coil cord.

Wiring Ballasts and Terminal Strips

Procedure to wire the ballasts and terminal strips.

Appendix VI-CE Racked Assembly

Attaching Outriggers and Jacks

Procedure to install the two outriggers and outrigger jacks.

Attaching the Rear Jack

Procedure for installing the rear jack.

Attaching the Tower Cradle

Procedure to assemble the tower cradle.

Installing the Tower

Procedure to install the tower assembly onto the Light Tower enclosure.

Attaching Light Mount Bracket and Bar

Attach light mount bracket to tower and light bar to bracket.

Attaching the Lights

Procedure to attach the four light fixtures to the light bar.

Wiring the Junction Box

Procedure to connect the wiring at the junction box.

Routing the Coil Cord

Procedure for routing the coil cord.

Wiring Ballasts and Terminal Strips

Procedure to wire the ballasts and terminal strips.

Wacker Neuson LTN 6L Specifications

General IconGeneral
Power SourceDiesel Engine
Light TypeMetal Halide
Number of Lights4
Fuel TypeDiesel
Lamps4 x 1000 W
Sound Pressure Level67 dB(A) at 23 ft (7 m)
Mast Height23 ft (7 m)
Weight1, 640 lb (744 kg)

Related product manuals