© WASP S.r.l.
Summary
0 Introduction ..................................................................... 5
0.1. Aim of the instruction manual ............................................ 5
0.2. How to read the manual of instructions ........................ 6
0.3. Storage of the manual of instructions ........................... 6
0.4. Updating the manual of instructions .............................. 6
1 General information ....................................................... 7
1.1. Manufacturer identification data ......................................7
1.2. Indentification label ................................................................ 7
1.2.1. Position of the label on the printer .....................................8
1.3. Testing ..........................................................................................8
1.4. Warranty ......................................................................................8
1.5. General safety warnings.......................................................9
1.5.1. Personal protective equipment ...........................................9
1.5.2. Operators for whom the manual is intended .............. 10
1.5.3. Protection systems ................................................................ 10
1.5.4. Residual risks ............................................................................10
1.5.5. Safety stickers ..........................................................................12
1.6. Glossary and pictograms .................................................. 12
1.6.1. Identification of operating personnel ............................12
1.6.2. Editorial pictograms ...............................................................13
2 Description of the printer .......................................... 15
2.1. Control panel / Material storage .................................... 16
2.2. Work area ................................................................................. 17
2.3. External area of the printer .............................................. 18
2.4. Extruder .................................................................................... 19
2.5. VACS - Vacuum Active Control System .................... 20
2.6. Technical data ........................................................................ 22
2.7. Noisiness .................................................................................. 23
2.8. Intended use of the printer .............................................. 23
2.9. Improper use of the printer .............................................. 23
3 Transport and handling ..............................................24
3.1. General warnings .................................................................. 24
3.1.1. Delivery of the printer ............................................................24
3.2. Content ..................................................................................... 25
3.3. Unpacking, lifting and handling of the printer ......... 25
4 Installation .......................................................................26
4.1. General warnings .................................................................. 26
4.1.1. Placement ................................................................................... 26
4.2. Electrical connection .......................................................... 27
4.3. Pneumatical connection ................................................... 27
5 Preparing to use the printer .....................................29
5.1. General warnings .................................................................. 29
5.2. User interface ......................................................................... 30
5.2.1. Main board ..................................................................................30
5.2.2. PRINT MENU ..............................................................................31
5.2.3. PREPARE menu ........................................................................32
5.2.4. ADVANCED menu ...................................................................33
5.2.5. WIFI settings .............................................................................. 34
5.2.6. GCODE .........................................................................................35
5.2.7. PRINTING board ....................................................................... 36
5.2.8. TUNE menu .................................................................................37
5.2.9. Digit window...............................................................................38
6 First use of the printer ................................................40
6.1. General warnings .................................................................. 40
6.2. Preparing the 3D file............................................................ 40
6.3. Slicing software ..................................................................... 40
6.4. Calibration ................................................................................ 41
6.5. Loading of the material ...................................................... 41
6.6. Placing the printing plate on the vacuum bed ......... 42
6.7. Selecting gcode .................................................................... 42
6.8. Function during the print ................................................... 42
6.9. Removal of the printing plate .......................................... 42
6.10. Detaching of the printed parts .................................... 42
7 Ordinary and extraordinary maintanance ..........43
7.1. General warnings .................................................................. 43
7.2. Ordinary maintanance ........................................................ 44
7.2.1. Pellet filter ...................................................................................45
7.2.2. Arms ball joint ............................................................................46
7.2.3. Extruder fans ............................................................................. 46
7.2.4. Sliders ...........................................................................................46
7.2.5. VACS (Vacuum Active Control System) ........................46
7.2.6. Nozzle ...........................................................................................46
7.3. Extraordinary maintenance ............................................. 47
7.3.1. Purging the extruder ..............................................................48
7.3.2. Changing the extruder .......................................................... 49
7.3.3. Manual leveling .........................................................................54
8 Use of the printer ..........................................................57
8.1. Adhesion to the bed ............................................................ 57
8.2. Clean Extruder ....................................................................... 58
8.3. Deleting .gcode from the machine ............................... 59
8.4. Free zeta system.................................................................. 60
8.5. Loading .gcode ...................................................................... 62
8.5.1. Loading with pendrive USB .................................................62
8.5.2. Loading with Wi-fi ....................................................................62
8.6. Loading/unloading the material ..................................... 64
8.7. Manual control ....................................................................... 66
8.8. Network and printing server ............................................ 68
8.8.1. Wi-fi connection .......................................................................68
8.8.2. Wired connection (Static IP) ............................................... 68
8.8.3. Printer server.............................................................................68
8.8.4. Printer server features ..........................................................69
8.9. Resurrection system ........................................................... 70
8.10. Set Z max ............................................................................... 70
8.11. Temperature controls ..................................................... 72
8.12. VACS (Vacuum Active Control System) .................. 74
9 Additional Instructions ............................................... 76
9.1. General warnings .................................................................. 76
9.2. Disposal and dismantling .................................................. 76
9.3. Instructions for emergency situations ....................... 77
To Next Page
Loading...
