3.2 Operating Procedures for Utility Functions
3.2.42 INDEXER Parameter Setting Initialization (FnB0B)
3-133
• The RES command must not being executed.
Operating Procedure
* If the key is pressed in an operation prohibited state, “Error.” is displayed for
approximately 2 seconds and then the display returns to the FnB0B operation screen.
In this case, make the setting again by referring to Preparation on page 3-132.
Step Operation Result
1
Press the key to open the Util-
ity Function Mode main menu, and
move the cursor with the
keys to select FnB0B.
2
Press the key to view the
FnB0B operation screen.
3
Press the key to start initializa-
tion of the parameters.*
Do not turn off the control power
supply until initialization has been
completed normally.
To cancel the FnB0B operation,
press the key before pressing
the key. The display returns to
the Utility Function Mode main
menu without executing the opera-
tion.
4
When parameter initialization has
been completed normally, “Done.”
is displayed.
5
Press the key to return to the
Utility Function Mode main menu.
6
To bring the settings into effect, turn the SERVOPACK power supply off
and back on.
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸿ࠉ㹋㹭㹬㹧㹲㹭㹰
㹄㹬㹀㸮㹀ࠉ㹎㹰㹫ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㹁ࠉ㸿㹊㹋ࠉ㹐㹣㹱㹣㹲
㹄㹬㹀㸮㹂ࠉ㹇㹬㹢㹣㹶㹣㹰ࠉ㸿㹊㹋
㹀㹀ࠉࠉࠉࠉࠉࠉ㹎㹰㹫㹇㹬㹧㹲
ࠉ㹑㹲㹟㹰㹲ࠉ㸸㹙㹂㸿㹒㸿㹛
ࠉ㹐㹣㹲㹳㹰㹬㸸㹙㹑㹃㹒㹛
㹀㹀ࠉࠉࠉࠉࠉࠉ㹎㹰㹫㹇㹬㹧㹲
㹐㹣㹱㹲㹭㹰㹧㹬㹥ࠉ㹬㹭㹵㸬㸬㸬
㹎㹪㹣㹟㹱㹣ࠉ㹵㹟㹧㹲㸬
㹀㹀ࠉࠉࠉࠉࠉࠉ㹎㹰㹫㹇㹬㹧㹲
㹂㹭㹬㹣㸬
㹎㹰㹣㹱㹱ࠉ㹙㹑㹃㹒㹛ࠉ㹩㹣㹷㸬
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸿ࠉ㹋㹭㹬㹧㹲㹭㹰
㹄㹬㹀㸮㹀ࠉ㹎㹰㹫ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㹁ࠉ㸿㹊㹋ࠉ㹐㹣㹱㹣㹲
㹄㹬㹀㸮㹂ࠉ㹇㹬㹢㹣㹶㹣㹰ࠉ㸿㹊㹋
To Next Page
Loading...
Need help?
General
