YASKAWA E-7 Series - Program Table Initialization (Fnb06)

3.2 Operating Procedures for Utility Functions
3.2.37 Program Table Initialization (FnB06)
3-120
* If the key is pressed in an operation prohibited state, “Error.” is displayed for
approximately 2 seconds and then the display returns to the JOG speed table editing
screen. In this case, make the setting again by referring to Preparation on page 3-
118.
3.2.37 Program Table Initialization (FnB06)
This function initializes the program tables and restores the settings on
shipment from the factory.
Preparation
Always check the following before you initialize a program table.
• The parameters must not be write-prohibited (Fn010 must be set to
0000).
• The program must not be running or on hold.
• A program table save operation must not be in progress for any
means other than the digital operator.
• Execution of the RES command must not be in progress.
3
Move the cursor with the
keys to select “STORE”.
Note: Selecting “CANCEL” and pressing
the key will return the display
to the JOG speed table editing
screen.
4
Press the key to start saving
the JOG speed table to flash mem-
ory.*
Do not turn off the control power
supply until saving has been com-
pleted normally.
5
When saving to flash memory has
been completed normally, the dis-
play returns to the JOG speed table
editing screen.
6
Press the key to return to the
Utility Function Mode main menu.
Continued from previous page.
Step Operation Result
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹑㹒㹍㹐㹃ࠉ㹈㹑㹎㹂ࠉ㹒㸿㹀㹊㹃㸽
ࠉࠉ㹁㸿㹌㹁㹃㹊ࠉ㹑㹒㹍㹐㹃
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹑㹲㹭㹰㹧㹬㹥ࠉ㹬㹭㹵㸬㸬㸬
㹎㹪㹣㹟㹱㹣ࠉ㹵㹟㹧㹲㸬
㹀㹀ࠉࠉࠉࠉࠉ㹈㹱㹮㹢㹃㹢㹧㹲
㹈㹑㹎㹂㸮㸮㸮㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸯㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸰㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹈㹑㹎㹂㸮㸮㸱㸻㸮㸮㸮㸮㸯㸮㸮㸮
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸲ࠉ㹘㹍㹌㹃ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸳ࠉ㹈㹑㹎㹂ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸴ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸵ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲