3.2 Operating Procedures for Utility Functions
3.2.37 Program Table Initialization (FnB06)
3-121
Operating Procedure
* If the key is pressed in an operation prohibited state, “Error.” is displayed for
approximately 2 seconds and then the display returns to the FnB06 operation screen.
In this case, make the setting again by referring to Preparation on page 3-120.
Step Operation Result
1
Press the key to open the Util-
ity Function Mode main menu, and
move the cursor with the
keys to select FnB06.
2
Press the key to view the
FnB06 operation screen.
3
Press the key to start program
table initialization.*
Do not turn off the control power
supply until initialization has been
completed normally.
To cancel the FnB06 operation,
press the key before pressing
the key. The display returns to
the Utility Function Mode main
menu without executing the opera-
tion.
4
When program table initialization
has been completed normally,
“Done.” is displayed.
5
Press the key to return to the
Utility Function Mode main menu.
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸳ࠉ㹈㹑㹎㹂ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸴ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸵ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸶ࠉ㹈㹑㹎㹂ࠉ㹇㹬㹧㹲
㹀㹀ࠉࠉࠉࠉࠉࠉ㹎㹥㹫㹇㹬㹧㹲
ࠉ㹑㹲㹟㹰㹲ࠉ㸸㹙㹂㸿㹒㸿㹛
ࠉ㹐㹣㹲㹳㹰㹬㸸㹙㹑㹃㹒㹛
㹀㹀ࠉࠉࠉࠉࠉࠉ㹎㹥㹫㹇㹬㹧㹲
㹐㹣㹱㹲㹭㹰㹧㹬㹥ࠉ㹬㹭㹵㸬㸬㸬
㹎㹪㹣㹟㹱㹣ࠉ㹵㹟㹧㹲㸬
㹀㹀ࠉࠉࠉࠉࠉࠉ㹎㹥㹫㹇㹬㹧㹲
㹂㹭㹬㹣㸬
㹎㹰㹣㹱㹱ࠉ㹙㹑㹃㹒㹛ࠉ㹩㹣㹷㸬
㹀㹀ࠉࠉࠉࠉࠉ㹄㹓㹌㹁㹒㹇㹍㹌
㹄㹬㹀㸮㸳ࠉ㹈㹑㹎㹂ࠉ㹃㹢㹧㹲
㹄㹬㹀㸮㸴ࠉ㹎㹅㹋ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸵ࠉ㹘㹍㹌㹃ࠉ㹇㹬㹧㹲
㹄㹬㹀㸮㸶ࠉ㹈㹑㹎㹂ࠉ㹇㹬㹧㹲
To Next Page
Loading...
Need help?
General
