ABB Switzerland Ltd REG 316*4 1MRB520049-Uen / Rev. C
6-8
6.7. HEX dump
Additional information to the diagnostic information is available
by selecting ‘Diagnostics’ from the main menu and then ‘Load
HEX dump’. Most of this data cannot be evaluated by the user,
but they are frequently useful to ABB personnel for fault-finding.
Once the data has been read, it should be deleted again by
selecting ‘Delete HEX dump’ to make room for saving new data.
ÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ
ÛABB Switzerland LtdÛÛÛÛÛÛÛÛÛÛÛÛExampleÛÛÛÛÛÛÛÛÛÛÛÛÛREG316*4 Generator TerminalÛ
ÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ
ÛÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»Û
Ûº ºÛ
Ûº1000:0000 0004 Error code = stopped ºÛ
Ûº1000:0002 0000 Code segment = 0588H ºÛ
Ûº1000:0004 0164 Module name = PARDEFST_TEXT ºÛ
Ûº1000:0006 0588 Program counter = 0164H ºÛ
Ûº1000:0008 0004 ºÛ
Ûº1000:000A 0002 ºÛ
Ûº1000:000C 03F0 ºÛ
Ûº1000:000E 0418 EEPROM: 00000000000000101 ºÛ
Ûº1000:0010 0EE4 ºÛ
Ûº1000:0012 0100 ºÛ
Ûº1000:0014 14B1 ºÛ
Ûº1000:0016 07C8 ºÛ
Ûº1000:0018 1B7C ºÛ
Ûº1000:001A 17E9 ºÛ
Ûº1000:001C 01AD ºÛ
Ûº1000:001E 0005 ºÛ
ÛÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼÛ
ÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ
ÛOn-line 9600 bps SCS:SPAÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛV6.2b | V6.2bÛ
ÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ
Fig. 6.3 HEX dump
6.8. IBB information
Depending on the firmware installed and therefore the choice of
the interbay bus, various data on the status of the bus in relation
to the station control system and the PC card can be obtained
via this menu item.
6.8.1. SPA bus
No special information is available about the SPA bus.
To Next Page
Loading...
