Index-4
Index
flat limit lines, 1-73
floppy disk, what you can save
,
4-37
form feed sequence
, 4-26
sending to the printer
, 4-26
format
, 7-8
format arrays
, 7-8
format markers, polar
, 1-32
formats, analyzer display
, 7-24
formatting a disk
, 4-54
forward stepping in edit mode
,
1-106
forward transform
measurements
, 3-22
demodulating the results of the
forward transform
, 3-23
forward transform range
, 3-24
interpreting the forward
transform horizontal axis
,
3-23
interpreting the forward
transform vertical axis
, 3-22
forward transform mode
, 3-4
forward transform range
, 3-24
four-channel display
4 Param Displays softkey
, 1-18
Channel Position softkey
, 1-17
customizing
, 1-17
viewing
, 1-14
Freelance, using
, 4-23
frequency
segments, editing
, 6-34
signals, deleting
, 6-35
span, decreasing
, 5-11
span, setting
, 1-36
frequency bands
adding
, 1-85
changing
, 1-84
deleting
, 1-86
setting
, 1-83
frequency drift
, 5-5
frequency list sweep of 26 points
,
2-29
frequency offset mode operation
,
2-9
frequency offset mode, conversion
compression
, 2-40
frequency offset mode, conversion
loss
, 2-13
frequency offset operation
, 7-85
frequency range, setting
, 1-5
frequency range, setting for time
domain low pass
, 3-15
frequency response
, 7-41
frequency response and isolation
error corrections
, 6-17
reflection measurements
, 6-19
transmission measurements
,
6-17
frequency response error
corrections
, 6-12
receiver calibration
, 6-15
response error correction for
reflection measurements
,
6-12
response error correction for
transmission
measurements
, 6-14
frequency response of calibration
standards
, 6-6
electrical offset
, 6-6
fringe capacitance
, 6-6
fringe capacitance
, 6-6
full two-port calibration
, 7-55
full two-port error correction
, 6-29
G
gain
, 1-57
gain compression
measuring
, 1-53
using linear sweep
, 1-55
gating
, 3-35, 7-7
selecting gate shape
, 3-36
setting the gate
, 3-35
general
, 8-7
generating files in a loop counter
example
, 1-116
German FTZ emissions
requirements
, 8-8
gosub sequence command
, 1-107
GPIB operation
address menu
, 7-80
GPIB STATUS indicators
, 7-79
local key
, 7-78
pass control mode
, 7-79
system controller mode
, 7-79
talker/listener mode
, 7-79
using the parallel port
, 7-80
GPIO mode
, 1-107, 7-81
graphic files
saving measurement results as
,
4-46
grids
moving marker information off
the grids
, 1-26
group delay
, 1-46
group delay format
, 7-25
group delay measurements
, 2-35
group delay principles
, 7-29
H
high dynamic range
measurement
, 2-24
swept RF/IF conversion loss
,
2-20
high dynamic range
measurement
, 2-24
high dynamic range swept RF/IF
conversion loss
measurement parameters for IF
range
, 2-20
power meter calibration over IF
range
, 2-20
power meter calibration over RF
range
, 2-23
receiver calibration over IF
range
, 2-22
RF frequency range
, 2-22
high power
measurements
, 1-59, 1-65
high power measurements
additional setup
, 1-60
attenuator settings, selecting
,
1-61
final setup
, 1-63
initial setup
, 1-59
power levels, determining
, 1-59
power ranges, selecting
, 1-61
horizontal axis
, 3-13, 3-14, 3-16,
3-20, 3-23
how RF and IF are defined
, 2-7
how to
make high power
measurements
, 1-59
HPGL
compatible printer
, 4-21
initialization sequence, sending
to the printer
, 4-26
initialization sequence, storing
,
4-25
HPGL compatible printer
, 4-25
HPGL/2 compatible printer
, 4-10
I
IF bandwidth reduction
, 7-35
IF bandwidth, setting segment
,
7-19
IF delay, detecting
, 5-11
IF detection
, 7-6
IF range
measurement parameters
, 2-20
power meter calibration
, 2-20
receiver calibration
, 2-22
IF, defining
, 2-7
imaginary format
, 7-29
improving measurement results
,
5-8
decreasing the sweep rate
, 5-9
decreasing time delay
, 5-9
To Next Page
Loading...
Need help?
General
