Need help?Do you have a question about the Allen-Bradley Stratix 8000 and is the answer not in the manual?
General| Brand | Allen-Bradley |
|---|---|
| Model | Stratix 8000 |
| Category | Switch |
| Language | English |
Introduces Express Setup for initial switch configuration tasks like IP assignment and global macro execution.
Explains the three modes of Multi-mode Express Setup: Short, Medium, and Long Press, with a summary table.
Guides users on configuring network settings via Device Manager after running Express Setup, including troubleshooting.
Explains how to configure network settings for the switch using the Logix Designer application after Express Setup.
Introduces Device Manager as a web-based tool for configuring, monitoring, and troubleshooting switches.
Explains how to manage the switch using the Logix Designer application within the Studio 5000 environment.
Guides users on how to download and apply firmware updates to switches using Device Manager.
Guides users on mounting the switch on a rack, referring to bracket attachment and switch mounting procedures.
Details the procedure for mounting the switch on a wall, including minimum clearances for enclosures.
Details the steps for wiring the DC power source to the switch, including opening the cover and connecting wires.
Explains how to verify switch operation by powering it on and checking status indicators after installation.
Details the procedure for mounting the switch on a DIN rail, including clearances and orientation.
Details the steps for wiring the DC power source to the switch, including connector and wire specifications.
Explains how to attach the switch power connectors to the front panel, including torque specifications.
Guides users on wiring the DC power source for PoE expansion modules, including power input requirements.
Details how to wire external alarms using the switch's alarm input and output relay circuits.
Describes how to connect devices to 10/100/1000 Ethernet ports, including autonegotiation.
Guides users on connecting devices to 10BASE-T, 100BASE-TX, or 1000BASE-T ports, including cable types.
Explains how to connect devices to PoE ports, referring to power supply requirements.
Details how to connect fiber-optic cables to SFP module ports, including port status indicators.
Describes how to connect devices to dual-purpose ports using RJ45 connectors or SFP modules.
Lists the necessary items and tools for installing the Stratix 8000/8300 switches, including expansion modules and console cable.
Guides users on attaching expansion modules to the switch base unit before mounting, with safety precautions.
Guides users on installing SFP modules for fiber-optic communication, including precautions.
Provides instructions for properly grounding the switch to connect it to a protective ground.
Details the steps for wiring the DC power source to the switch, including locating and connecting the power connector.
Guides users on wiring the DC power source to the PoE expansion module, including power input requirements.
Guides users on configuring ACLs via Device Manager, showing existing ACLs and how to apply them to ports.
Details the steps to create an ACL entry, including defining type, name, number, and conditions for packet matching.
Guides users on configuring alarm relay settings via Device Manager, including normally open and normally closed contacts.
Guides users on configuring time synchronization using Device Manager, including PTP clock modes and settings.
Details how to configure DHCP for ring devices to assign IP addresses based on ring position, ensuring expected IP.
Guides users on configuring DLR on the switch via Device Manager, covering ring node and supervisor setup.
Explains how to configure DLR, redundant gateways, and DHCP for ring devices using the Logix Designer application.
Explains DHCP persistence to assign specific IP addresses to ports, ensuring consistent device IP.
Details the process of using DHCP persistence to assign specific IP addresses to ports, ensuring consistent device IP.
Guides users on creating a DHCP address pool after enabling DHCP, including pool name and IP address range configuration.
Details how to assign specific IP addresses to each port using the Logix Designer application for DHCP Address Assignment.
Guides users on configuring EtherChannels via Device Manager, including channel group number, mode, and ports.
Explains how to add, edit, and delete EtherChannel members using the Logix Designer application.
Guides users on applying or removing QoS macros via Device Manager to prioritize motion traffic.
Details how to configure NAT instances via the Logix Designer application for Stratix 5410 switches.
Provides steps to create NAT instances for traffic routed through a Layer 3 switch or router, including private-to-public translations.
Guides users on creating NAT instances for traffic routed through a Layer 2 switch, including VLAN assignments.
Explains how to use the Device Manager Dashboard window to monitor switch status and performance, including front panel views.
Describes how to view switch status parameters within the Studio 5000 Logix Designer application.
Explains the Power-On Self-Test (POST) process and how status indicators reflect its success or failure.
Explains how to access Device Manager via a physical connection in Direct Managed mode when the switch IP address is unknown.
Guides users on restarting or resetting the switch to resolve issues, with options to save or discard configuration.
To Next Page
