Alpine PXA-H800 - PC Software Advanced Functions

From
a
PC
When you connect an external input source, you can name it with a
suitable name (Initial setting:
"Auxiliary").
1
Click
['t']
for each AUX and select and click the
external input product name from the pull-down
menu.
Setting item: AUX Name
Setting contents: Auxiliary/TV/EXT.DVD/Portable/Game
•
This item becomes possible to set only when
AUXIN
setting is on.
Setting/Adjusting
the
Navigation
Guidance
Volume
(Navi
Mix)
If
a navigation system is connected, its voice guidance will be mixed
with the system and output from the front speakers (Initial setting:
"OFF").
You
can adjust the navigation guidance volume (Initial settin
g:
"OdB").
1
Click
[ON]
or
[OFF]
for
"Navi Mix"
in the main menu.
·,
'.
Na\111\1IX
• '
•II
-·
'.'FF
) (
.,.
+
2
•JB
..._
If
you
click [ON], select the setting
value.
2
Click
['t']
or
L&]
to
adjust the volume.
Setting contents:
-10
to
+
10
dB
•
For details on the connection
of
a navigation system,
ref
er to the
installation manual.
16-EN
Automatic
Measurement
Function
Before
Performing
Automatic
Measurement
This unit is equipped with ImprintEQ, RoadEQ, and AutoTCR
automatic measurement functions.
~WARNING
•
Do
not
p
erform
automatic measurement
while
the vehicle is
running.
Automatic
measurement
requires microphones to
be
installed
in
the
cabin
to
measure acoustic characteristics, and the
speakers
may
output
loud
noise for measurement.
This
may
interfere
with
safe driving and lead to an accident.
Be sure to read before performing automatic
measurement.
•
The automatic measurement should be performed in a quiet place
with the engine, air-conditioner,
and
heater turned
off
If
a mobile
phone
or
car phone is installed
in
the vehicle, move them outside
of
the cabin, or turn the
power
off
Sound other than the measuring
so
und
(ambient noise around the vehicle, engine noise, and
ringtones) may interfere with measurement, resulting
in
inaccurate
measurement
of
the acoustic characteristics
of
the cabin.
•
Be aware that the battery
may
be
drained
if
you use the unit
for
an
extended period
of
time without running the engine.
•
The microphone supplied with this product is specifically designed
for
this type
of
measureme
nt
. Use
of
any other microphone will give
poor
or
no
results. Use
of
microphones other than the one supplied is
not
recommended.
•
If
the system is
equipped with a power amplifi
er
with input level
co
ntrol
or
a powered subwoofer, the measurement may not be
possible
if
the input level
is
set lo
w.
However, to perform correct
measurement, the input level should not be set too high.
•
For a power amplifier with low-pass filter, turn
off
the low-pass filter
of
the
pow
er amplifier to make measurement. The low-pass filter in
the power
ed
subwoofer
or
the pow
er
amplifier
for
a subwoofer
should be set
at
the highest cutoff frequency.
Measurement sequence for the automatic measurement
functions
Perform
the automatic measurement in the following sequence.
When lmprintEQ is used:
First,
lmprintEO,
then
RoadEO
.
When lmprintEQ is
not
used:
Fir
st,
Au
to
TCR,
then
Road
EO.
•
When lmprintEQ is us
ed
, AutoTCR
is
not required.
•
When lmprintEQ and AutoTCR are performed after RoadEQ, re-
perform RoadEQ.