Alpine PXA-H800 - Setting the Digital Input

From
the
Commander
Setting
the
Digital
Input
(Digital
AUX)
A TV
or
VCR
with
RCA
audio output can be connected to the unit.
Select
OFF
for any
ex
ternal input that is not connected (Initial setting:
"ON"
).
1 Press
[FUNC.].
2 Rotate the [Rotary encoder] to select "Input Setup,"
and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select "Digital AUX,"
and then press the [Rotary encoder].
The AUX selection screen is displayed.
4
Rotate the [Rotary encoder] to select "Digital1 ;·
and
then press the [Rotary encoder].
5
Rotate the [Rotary encoder] to select "ON"
or
"OFF,"
and then
press the [Rotary encoder].
II'DIGTAL
1
I
ON
'
6
Press [
=>
].
7
Rotate the [Rotary encoder] to select
"Digital 2,"
and
then press the [Rotary encoder].
8 Rotate the [Rotary encoder] to select "ON"
or
"
OFF,"
and then press the [Rotary encoder].
9
When the setting is complete, press and hold [
=>
]
for
at
least 2 seconds.
•
When
an
Ai-NET
compatible head unit is connecte
d,
external input
of
the
PXA-H800 becomes unavailable,
and
this setting
will
be
disabled.
•
If
[
=>
]
is
pr
essed during setting, the unit r
et
urns to the previous
item.
•
After the setting, it is recommend
ed
to store the setting contents on
the unit. For details, refer
to
"Storing
the
Preset
Values (Preset
Store)"
(page
36
).
Setting
the
AUX
Volume
Input
Level
(AUXIN
Gain)
If
the
ex
ternal input audio becom
es
distorted, select High. (Initial
setting:
"High")
1
Press
[FUNC.].
2
Rotate the [Rotary encoder] to select "Input Setup
,"
and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select
"AUXIN
Gain,"
and then press the [Rotary encoder].
The AUX sele
ct
ion screen is displayed.
40-EN
4
Select the AUX you want to set by rotating the
[Rotary encoder], and press the [Rotary encoder].
Settings item: AUX 1, AUX2, AUX 3
•
The number
of
AUX
vari
es
dep
end
ing on the
AUX
Input
Setup
(page 39).
5
Rotate the [Rotary encoder] to select
"High" or
"Low",
and then press the [Rotary encoder].
II'AUXl
·"'
.,:;
~~
I
-
Hi~h
-
J
High: When the volume
level of the external
input is high.
Low: When the volume
le
vel
of the external i
np
ut is
low.
6
To set another AUX, press [
=>
] and repeat Steps 4
and
5.
7
When the setting
is
complete, press and hold [
=>
]
for at least 2 seconds.
•
If
[
=>
J
is
pr
essed during setting, the unit returns to the previous
item.
•
After the setting, it is recommended to store the setting contents on
the unit.
For
details, refer to
"Storing
the
Preset Values (Preset
Store)"
(page 36).
Adjusting
the
AUX
Volume
Level
(AUX
Level)
You
can adjust the volume signal level
of
the external
RCA
inpu
t.
Adjust this when the volume is higher or lower compared to that
of
the
optical digital product. (Initial setting:
"0
dB")
1
2
3
4
Press
[FUNC.].
Rotate the [Rotary encoder] to select
"Input Setup,"
and then press the [Rotary encoder].
Rotate the [Rotary encoder] to select
"AUX Level,"
and then press the [Rotary encoder].
The AUX
Se
lec
ti
on
screen is displayed.
Select the AUX you want to set by rotating the
[Rotary encoder], and press the [Rotary encoder].
Settings item:
AUX 1/AUX 2/AUX 3/Ai-NET(HU)/
Ai
-
NET(CHG)
•
The numb
er
of
AUX
varies depe
nd
ing on the
AUX
In
put
Setup
(page 39)
.
5 Adjust the volume level by rotating the [Rotary
encoder].
II'
AU
>::
1
'·-
·~
.'
'" .
LEVEL±
(]dE:
Setting
co
ntent
s:
-10
to
+
10
dB
6
To set another AUX, press [
=>
]
and repeat Steps 4
and
5.