Alpine PXA-H800 - Setting the Speakers; Setting the Subwoofer Output

From
the
Commander
*
1
When you modify the
"FRONT HIGH"
speaker setting to [Full], a
message
to confirm the change will
be
displayed.
To
set up
at
"F
ull
Range,"
rotate the [Rotary encoder] to select
"OK",
and then press
the [Rotary encoder]. Make sure the speaker being used
for
this
output is able to handle a full range sou
rce.
Many tweeters can
be
damaged when driven by a full range signal.
*
2
This item is enabled for setup only when 2 subwoofers are connected.
Rotate the [Rotary encoder] to select
"Stereo"
or
"Mono",
and
then
press the [Rotary encoder].
Stereo: Subwoofer stereo (LIR) output
Mono: Subwoofer
monaural output
•
Speakers that cannot be turned
off
are disabled
for
setup. Refer to
Table I (Output
System) in
"System Configuration"
(page
60).
•
When you connect
just
one subwoofer; turn
off
"Subwoofer2."
7
·1First
time start-up:
The
AUX
Input
System Select screen
will
be
automatically
displayed. Continue
to
set, referring to
"Setting
the
AUX
Input
System
(AUX
Input Setup)"
(page 39).
7
·2subsequent
start-up:
The
"Turn
ACC
Off" screen
will
be
displayed.
Turn
the
ignition
key
to
off and then on again. The settings
become effective.
•
If
[
~
]
is pressed during setting, the unit returns
to
the previous
item.
•
If
the speaker system
is
changed, all setup values except those
for
AUX
input will be restored to the initial setup value
s.
•
You
can also set the speakers from "Setting
the Speakers (Speaker
Setup)" (page 38).
•
You
can also set the subwooferoutputfrom
"Setting
the Subwoofer
Output (SW Channel)"
(page 38).
•
After the setting, it is recommended to store the setting contents
on
the unit. For details, refer to
"Storing
the Preset Values (Preset
Store)"
(page 36).
Setting
the
Speakers
(Speaker
Setup)
Turn
on
the connected speakers.
1 Press [FUNC.].
2 Rotate the [Rotary encoder] to select
"Output
Setup,"
and then press the [Rotary encoder).
3
Rotate the [Rotary encoder] to select
"Speaker
Setup," and then press the [Rotary encoder).
The Speaker
selection
screen is displayed.
4
Rotate the [Rotary encoder]
to
select the speaker to
be set, and then press the (Rotary encoder].
Setting contents Front High/Front Mid/Front Low/Rear/
Center/Subwoofer ( 1, 2)
•
Speakers to be set vary depending on the system set in
"S
etting
the
Speaker
System
(System
Select)"
(page
37).
•
Spe
ak
ers that cannot be turned
off
ar
e disabled
for
setup. Ref er to
Table 1
(Output
System) in
"System Configuration"
(page
60).
38-
EN
5
Rotate the [Rotary encoder] to select
"ON"
or
"OFF,"
etc., and then press the [Rotary encoder].
Repeat the steps until all
the speakers are set.
Front High*:
Front Low:
Rear:
Center:
Subwoofer(1,
2):
OFF{Tweeter/Full
OFF/ON
OFF/ON
OFF/ON
OFF/ON
*
When you modify the "Front High"
speaker setting to [Full], a
message
to
confirm the change will
be
displayed.
To
set up
at
"F
ull
Range,"
rotate the
[Rotaty
encoder} to select
"OK"
,
and then press
the [Rotary encoder]. Make sure the speaker being used
for
this
output is able
to
handle a full range source. Many tweeters can be
damaged when driven by a full range signal.
•
When you connect
just
one subwoofer; turn
off
"Subwoofer2."
6
To
set up other speakers, press [
~
] and repeat
Steps 4 and 5.
7
When the setting is complete, press and hold (
~
]
for at least
2
seconds.
•
lf
[
~
] is pressed during setting, the unit returns to the previous
item.
•
When the speaker setting
is
changed while lmprintEQ/RoadEQ is on,
lmprintEQ/RoadEQ will be turned
off
after a confirmation message
is display
ed
.
•
After the setting, it is recommended
to
store the setting contents on
the unit.
For
details, refer to
"Storing
the Preset
Valu
es (Preset
Store)"
(page 36).
Setting
the
Subwoofer
Output
(SW
Channel)
You
can
set
the subwoofer output to stereo
or
monaural. Make sure to
set the correct output for your subwoofer type. (Initial Setting: "Mono")
1 Press [FUNC.].
2 Rotate the [Rotary encoder] to select
"Output
Setup,"
and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select
"SW Channel,"
and then press the [Rotary encoder].
The
Su
bwoofer
Channel selection
screen is
displayed.
4 Rotate the [Rotary encoder]
to
select "Mono"
or
"Stereo;·
and then press the [Rotary encoder].
II"SWCHANNEL
,
~
,
~
M~no
:
f
'
1
~
>
Mono: Subwoofer
monau
ral
output
Stere
o:
Subwoofer stereo (LIR) output