Alpine PXA-H800 - Using Dolby Prologic II

8
When the setting is
complete,
press and hold
[
~]
for at least 2 seconds.
•
If
[
~
] is pressed during setting, the unit returns to the previous
item.
• When both Rear
and
Center speakers are
off
in
"Setting
the Speaker
System (System Select)"
(page
37)/"Setting
the Speakers (Speaker
Setup)"
(page 38), this item cannot
be
set.
•
This function only works with 2-channel signals.
• After the setting, it is recommended to store the setting contents on
the unit. For details, refer
to
"Storing
the Preset
Values
(Preset
Store)" (page
36
).
Using
Dolby
Pro
Logic
II
(Dolby
PLII)
Pro Logic processing can be applied to the music signals recorded in 2-
channel stereo. This gives normal 2-channel stereo a more live, concert
hall effect. When you select
"Music," you can adjust the center width.
This function provides the optimum vocal
localization by adjusting the
center channel lo
ca
lization in between the center speaker and the L/R
speakers. (Initial setting:
"Music")
1
Press [FUNC.].
2
Rotate
the
[Rotary encoder] to
select "Playback
Mode,"
and then press the [Rotary encoder].
3
Rotate
the
[Rotary encoder] to
select "Mode," and
then press the [Rotary encoder].
The Mode selection screen is displayed.
4
Rotate the [Rotary encoder] to
select "Dolby PLII,"
and then press the [Rotary encoder].
5
Press[~].
This will take you back to the
Step
3 screen.
6 Rotate the [Rotary encoder]
to
select "Dolby PLII,"
and then press the [Rotary encoder].
The
DOLBY
PLII
screen is displayed.
7
Rotate
the
[Rotary encoder]
to
select "Music"
or
"Movie;'
and then press the [Rotary encoder].
II'
DOLBY
PLll
Music
Music:
Suits
the stereo
TV
shows and all programs
encoded
in
Dolby Surround.
It
improves
the sound
field directivity to near that of discrete
5.
1-channel
sound.
Movie: Can
be
used for a
ll
stereo music
re
cordings, and
provides a wide,
deep
sound field.
From
the
Commander
8
When the setting is
complete,
press and hold
[
~
]
for
at
least
2 seconds.
•
If
[
~
]
is
pressed during setting, the unit returns to the previous
item.
•
For the details
of
Dolby
Pro
Logic II, see page 61.
•
When both Rear
and
Center speakers are
off
in
"Setting
the Speaker
System (System Select)"
(page
37)/"Setting
the Speakers (Speaker
Setup)"
(page 38), this item cannot be set.
•
This function only works with 2-channel signals.
•
After
the setting,
it
is recommended to store the setting contents on
the unit. For details, refer to
"Storing
the
Preset
Values
(Preset
Store)"
(page 36).
Adjusting the Center Width (Center Width)
When you
se
lect
"Music" for
"Dolby Pro
Logic
II,"
you can further
adjust the center width in the following steps.
This function offers the
optimum vocal position by adjusting the center channel position
between the center speaker and the
UR
speaker. (The adjustments
established in
"Adjusting
the Acoustic Image
(BI-PHANTOM)"
(page 55) are ineffective while this function is activated.) (Initial setting:
"OFF
', "Level 0")
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select "Playback
Mode;' and then press the [Rotary encoder].
3 Rotate the [Rotary encoder] to
select "Center Width,"
and then press the [Rotary
encoder].
4 Rotate the [Rotary encoder]
to
select "ON,"
and then
press the [Rotary
encoder].
II'
C:Et
·
lTER
WI
DTH
l!ID
[]
5
Adjust the
level
by rotating the [Rotary encoder].
LEVEL:
0
to 7
When the level becomes high
er,
the center channel
localization shifts from the center speaker toward both
sides.
6
When the setting is
complete,
press and hold
[
~
]
for
at
least
2 seconds.
•
When the Center speaker is
off
in
"Setting
the Speaker
System
(System
Selec
t)"
(page
37)/"Setting
the Speakers (Speaker
Setup)"
(page 38), this item cannot be set.
•
After
the setting, it is recommended to store the setting contents on
the unit. For details, refer to "Storing
the
Pr
eset
Values
(Preset
Store)"
(page 36).
53-EN