5 Select the channel you want to adjust
by
pressing
[CHANNEL].
L+R selected: FRONT
---7
REAR
---7
CENTER
---7
SUBWOOFER*
1
---7
FRONT
Lor
R selected: FRONT L
---7
FRONT R
---7
REAR
L
---7
REAR
R
---7
CENTER
---7
SUBWOOFER*
2
---7
FRONT L
*
1
If
the Subwoofer output
is
set
for
Monaural, you can set both
SUBWOOFER 1 and
2.
*
2
If
the Subwoofer output
is
set
for
Monaural, you can set
SUBWOOFER 1 and
2.
If
the Subwoofer output is set for Stereo, you
can set SUBWOOFER
Land
R.
• Channels to
be
set vary depending on the system set
in
"Setting the
Speaker System (System Select)" (page 37).
6 Select the frequency by rotating the [Rotary
encoder], and press the [Rotary encoder].
fc:
FRONT/REAR/CENTER:
20Hz
to 20kHz (in 1/3 octave steps)
(1
to
31
Band)
SUBWOOFER:
20Hz
to
160Hz
(in 1/3 octave steps)
(1
to
10 Band)
7 Adjust the level
by
rotating the [Rotary encoder], and
press the [Rotary encoder].
Level: -12 to +12
dB
(in 0.5
dB
steps)*
3
*
3
When ImprintEQ is enabled, 6 to +6 dB (in 0.5 dB steps)
8
To
adjust another frequency, repeat Steps 6 and 7.
9
To
adjust another channel, repeat Steps 5 through 8.
•
You
can listen with Defeat OFF (adjusted setup values) or with
Defeat
ON
(Initial value) to compare, by following the steps below.
1 Press and hold the [Rotary Encoder] for at least 2
seconds
while
in
the adjustment mode.
2 Rotate the [Rotary Encoder] to switch on/off Defeat, and
listen
to
compare.
3
To
exit, select "OFF" and then press [
~
]
•
You
can mute the channel you are adjusting.
1 Press [MUTE] while
in
the adjustment mode to mute the
channel.
2
To
cancel muting, press [MUTE] again.
10
When the setting is complete, press and hold [
~]
for at least 2 seconds.
•
If
[
~
]
is
pressed during setting, the unit returns
to
the previous
item.
• This function is not available when Defeat
is
set
to
ON.
• When the speaker is set
to
the "OFF" mode, the graphic equalizer
for
that speaker cannot
be
set. Refer
to
"Setting the Speaker System
(System Select)" (page 37) /"Setting the Speakers (Speaker Setup)"
(page 38).
• Check the playable frequency ranges
of
the connected speakers
before making equalizer adjustments. 1fthe speaker's playable
frequency range is 55 Hz to 30kHz, for example, adjusting the
40Hz
or
20Hz
band has no effect. Moreover, you may overload and
damage the speakers.
• After the setting, it is recommended to store the setting contents on
the unit.
For
details, refer to "Storing the Preset Values (Preset
Store)" (page
36
).
From
the
Commander
Setting
the
Parametric
EO
The frequency bands
of
the graphic equalizer are fixed. This makes it
difficult to correct for undesired peaks and dips at specific frequencies.
The parametric equalizer's center frequency can be tuned to these
specific frequencies. The bandwidth
(Q) and level are then fine-tuned
independently, to make the necessary corrections. The parametric
equalizer function is an advanced tool for serious audiophiles.
• Set "Setting the Equalizer Mode (EQ Mode)" on page 46 to "P.EQ."
1 Press [FUNC.].
2 Rotate the [Rotary encoder] to select "Sound Field
Adj.," and then press the [Rotary encoder].
3 Rotate the [Rotary encoder] to select "EQ
Adjustment," and then press the [Rotary encoder].
The P-EO screen is displayed.
•
P-EG!
FRDt·H
'1
~
Band
10
fr:
~kHz:
0
1.0
level
+J0.0dE:
4 Press and hold [CHANNEL] for at least 2 seconds.
Rotate the [Rotary encoder] to select either "L+R" or
"L or
R,"
and press the [Rotary encoder].
Lor
R:
Channels
Rand
L can be set independently.
L+R: Both
Rand
L channels are set at the same value
(The initial setting).
• When you switch from
"Lor
R"
to
"L+R," choose which adjustment
of
the R and L channels to be applied.
1 Select either
"L---7
R"
or
"R
---7
L"
by
rotating the [Rotary
encoder, and press the [Rotary encoder].
L---7
R:
The adjustment of the L channel is to be applied
to
both R and L channels.
R
---7
L:
The adjustment of the R channel is to be applied to
both R and L
channels.
5 Select the channel you want to adjust by pressing
[CHANNEL].
L+R selected: FRONT
---7
REAR
---7
CENTER
---7
SUBWOOFER*
1
---7
FRONT
Lor
R selected: FRONT L
---7
FRONT R
---7
REAR
L
---7
REAR
R
---7
CENTER
---7
SUBWOOFER*
2
---7
FRONT L
*
1
If
the Subwoofer output
is
set for Monaural, you can set both
SUBWOOFER 1 and
2.
~If
the Subwoofer output
is
set for Monaural, you can set
SUB WOOFER 1 and
2.lfthe
Subwoofer output is set for Stereo, you
can set SUBWOOFER
Land
R.
• Channels to be set vary depending on the system set
in
"Setting the
Speaker System (System Select)" (page 37).
47-EN
To Next Page
Loading...
