Alpine PXA-H800 - Setting the Time Correction Adjustment Unit

•
When you switch from "
Lor
R"
to
"L
+R,"
choose which adjustment
of
the R
and
L channels to be applied.
1 Select
either
"L~
R"
or
"R~
L"
by
rotating the [Rotary
encoder]. and press the
[R
otary encoder].
~
51!tting
Data
l:opy
~
.
t
. . ·.
!:1m
L~
R: The adjustment of the L chan
nel
is to be applied to
both R and L channels.
R
~
L:
The adjustment of the R channel
is
to be applied to
both
Rand
L channel
s.
9
Select
the channel you want
to
adjust by pressing
[CHANNEL].
L+R selected:
FRONT
HIGH~FRONT
MID~
FRONT
LOW~
RE
A
R~
CENTER~
SUBWOOFER*
1
~FRONT
HIGH
L or R
se
l
ec
ted:
FRONT
L
HI
GH~
FRONT
R
HI
G
H~
FRONT
L
MID~
FRO
NT
R
MID~
FRON
T
L
LOW~
FRONT
R
L
OW~
REAR
L~REAR
R~CENTER~
SUBWOOFER*
2
~
FRONT
L
HIGH
*
1
If
the Subwoofer output
is
set
for
Monaural, you can set both
SUBWOOFER
I and
2.
,.2
If
the Subwoofer out
put
is
set
for
Monau
ral,
you can set
SUBWOOFER
I and
2.
If
the Subwoofer output is set
for
Stereo,
you
can set
SUBWOOFER
Land
R.
•
Channels to be set vary depending on the system
se
t in
"Setting
the
Speak
er
System (System Select)" (page 37).
10
Adjust the calculated time correction value
(0.00
to
20.00
ms) by rotating the [Rotary encoder].
Displaying the distances from the listening
positions to the speakers
Se
tting content
s:
0.00
to
20.00
ms (
in
0.05
ms steps)
•
The distances can be displayed in eith
er
"em"
or
"inch"
(see
"Setting
the
Tim
e Correction Adjustment Unit
(TCR Parameter)"
page
51).
11
To
adjust another channel, repeat
Steps
9 through
10.
•
You
can listen with Defe
at
OFF (adjusted setup values) or with
Def
eat
ON
(Initial value) to compare, by following the steps below.
1 P
re
ss
and
hold
th
e [Rotary Encode
r]
for at least 2
seconds wh
il
e
in
the adjustment mode.
2 Rotate the [Rotary
En
coder] to switch on/off Defeat, and
li
sten to compare.
3
To
exit, select
"OFF"
and then pre
ss
[
~
].
•
You
can
mut
e the channel you are adjusting.
1 Press
[MUTE] while
in
the
ad
justment mode to mute t
he
channe
l.
2
To
cancel mu
ti
ng, press
[MUTE] again.
From
the
Commander
12
When the setting is complete, press and
hold[~]
for
at
least 2 seconds.
•
If
[
~
]
is
pressed during setting, the unit returns to the previous
item.
•
This function is not available when Defeat is set to
ON.
•
When the speaker is set to the
"OFF" mode, the time correction
for
that speaker cannot be set. Refer to "Setting
the
Speaker System
(System Select)"
(page
37)/"Setting
the Speakers (Speaker
Setup)"
(page 38).
• After the setting, it is
re
co
mm
ended to store the setting contents on
the unit.
For
details,
re
fe
r to
"Storing
t
he
Preset Values (
Pr
eset
Store)"
(page 36).
Setting
the
Time
Correction
Adjustment
Unit
(TCR
Parameter)
The unit
of
measurement for time correction can be set as eith
er
"em"
or
"inch."
(Initial settin
g:
"em")
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select
"Sound
Field
Adj.," and then press the [Rotary encoder].
3
Rotate the [Rotary encoder]
to
select
"Setup,"
and
then press the [Rotary encoder].
4
Rotate the [Rotary encoder]
to
select
"TCR
Parameter," and then press the [Rotary encoder].
5
Select
either "em"
or
"inch"
by rotating the [Rotary
encoder], and press the [Rotary encoder].
em:
The
unit for the time correcti
on
becomes
"em."
inch:
The
unit tor the time cor
re
ction becomes
"inch."
6
When the setting
is
complete, press and hold [
~
]
for at least 2 seconds.
•
lf
[
~
]
is
pressed during setti
ng,
the unit returns to the
pr
evious
item.
51
-EN