.PRESET
Eall
~
5
Select
one from
"P.1"
through
"P.6"
by rotating the
[Rotary encoder], and press
the
[Rotary encoder].
--
'
'
The data is stored
in
the
selected
preset number.
•
The function is operable when Defeat
is
set to
OFF.
•
The
stored contents are
not
deleted even when resetting the unit
or
disconnecting the battery.
Recalling
a
Stored
Setting
(Preset
Call)
The
preset
memory
stores various setting/adjustment information. Thus,
it
takes s
ome
time
to
call data from
the
preset memory.
1
Press and hold [VIEW]
for at
least
2 seconds.
2
Select
a preset from
"P.1
" through "P.6" by rotating
the [Rotary encoder], and press the [Rotary
encoder].
The
values
of
the
selected
preset number are ret
ri
eved.
•
You
can
ca
ll
the
Preset
even
by
the following procedure:
1
Pre
ss
[FUNC.].
2
Rot
ate the [Rotary encoder] to select "
Pr
eset,
"a
nd then
press the [Rota
ry
encoder].
3
Ro
tate the [Rotary encoder] to select "Call
,"
and then
press the [Rotary encoder].
4
Select
a preset from
"P.1"
through
"P
.6"
by rotating the
[Rotary encoder], and press the [Rotary en
co
der].
The
values
of the
selected
preset number are retrieved.
•
The function
is
operable when
Def
eat
is
set to
OFF.
•
If
the speaker system in the preset
and
the current speaker system do
not match, the
pr
e
set
cannot
be
retrieved.
•
If
the
AUX
i
nput
system
in
the preset
and
the curre
nt
AUX
input
system do
not
mat
ch, the items concerning the
AUX
input system are
unavailable
for
retrieval.
Setting
the
Speaker
System
(System
Select)
Firs
t,
set
the
system
and
the speakers.
Unless you
set
the
system, you
ca
nnot
set
any
feat
ur
es.
Be
sure to
set
the
system first.
If
the
se
l
ected
system
and
the connections
of
the speakers
do
not
match, the speakers
may
be
damaged
.
Make
sure
to
check
the
co
nnections
of
the
speake
rs
before selecting
the
system.
From
the
Commander
Only
for the
initial startup:
1
Press
the
[FUNC.]
or
[Rotary encoder].
The
Ou
tput System selection screen is
displayed.
Go to
Step
3.
1
Press [FUNC.).
2
Rotate the [Rotary encoder) to
select "Output
Setup,"
and then press the [Rotary encoder].
3
Rotate the [Rotary encoder]
to
select "System
Select,"
and then press the [Rotary encoder].
The Output System selection
screen is
displayed.
4
Rotate the [Rotary encoder] to select a system, and
then press the [Rotary encoder].
.
'
.It
••
.
'
.
F-2way+R+SW: 4.2ch system
(Front2Way+Rear+Subwoofer)
F-
3way
+SW:
F-3way+R:
2.2ch system (Front3Way+Subwoofer)
4
Och
system (Front3Way+Rear)
F-
2way+R+C+SW: 5.1 ch system
(Front2Way+Rear +Center +Subwoofer)
•
Refer to Table 1 (Output System) in
"System Configuration"
(page
60).
5 Select "OK"
by rotating the [Rotary encoder] when a
confirmation message appears, and press the
[Rotary encoder].
1:
'.
System
Will
Be
Changed
'
'K
\
(!]3
' • J
"'
-
><>i
The
Speaker
Setup
screen is displayed.
•
When
"OK
"
is
selected, the
au
dio output
is
stopped until the ignition
key is turned
on/off
6
Turn off any unconnected speakers. Rotate the
[Rotary encoder] to
select "ON"
or
"OFF,"
etc., and
then press the [Rotary encoder].
.FRONT
HIGH
Tweeter
Repeat the steps
until a
ll
the speakers are set.
FRONT HIGH*L OFF{Tweeter/Fu
ll
FRONT
LOW:
OFF/ON
REAR
:
OFF/ON
CENTER:
OFF/ON
SUBWOOFER(1, 2):
OFF/ON
SW
CHANNEL Mono/Stereo*
2
37-EN
To Next Page
Loading...
