E!:
Both R and L channels are set at the same value (The
initial setting).
Ill:
Channels R and L can be set independently.
• When you select "II," a message
to
confirm which
of
the R
or
L
channel set up values is
to
be applied will be displayed. Click either
[LEFT] or [RIGHT].
3
Click
the
channel
you
want
to
adjust.
• Channels
to
be set vary depending on the system set in "Setting the
Speaker System (Output System
Select)" (page 13).
4 Drag
the
setup
point
up
or
down
or
to
the
right
or
left
to
make
adjustments.
The arrow indicating the dragging direction appears.
Frequency Level
Slope
Setup
point
The cutoff frequency band varies depending
on
the channel
(speaker) (see "About the Crossover (X-Over)" page 26).
Slope: 0 (OFF)/-6/-12/-18/-24/-30/-36 dB/oct*
Level: -24 to
OdB
(in 0.5 dB steps)
* Neither
LPF
of
Subwoofer nor HPF
of
Front High can be set
at
0
(OFF).
• Show
All
Curves:
When you click the [Show All Curves], the curves
for
all the channels
will be displayed.
• Hide Other Curves:
When you click the [Hide Other Curves], only the curve
of
the
channel
for
which you are making adjustments is displayed.
•
You
can also make adjustments by operating the settings indication
area.
The current setup value will be displayed
at
the bottom
of
the Screen.
Click
[T}
and select and click a setup value.
You
can also use the
[Tab}, [
f-
],
[
---7
}, [
1'
],
and [
J,
} keys on your PC to select the
setup value.
From a PC
HPF
lPF
Level Phase
l
ch
Freq
11kHZ •
_)
.?OO~H;:
~
Slop
• 1 _
dB
ud
•
l
~
FF
• U 0 dB • 180"
HPF
LPF
Level Phase
Rch
Freq
ll~H;:
LUU~H;:
~
S!Opi'
12
(J810d I
JFF
0 0
dB
180"'
• The unadjusted curve display can be turned
off
in the following steps.
1 Click the indicator of "Show."
Indicator
The indicator will be turned off and the curve display
of
the selected channel
is
hidden.
2
To
turn
on
the display, click the indicator of "Show" again.
5
Click
[0°]
or
[180°]
to
switch
the
phase.
6 To
adjust
another
channel, repeat
Steps
3
through
5.
• By clicking either
£1111
or
£111
of
"Mute" while in the adjustment
mode, you can mute the selected channel.
tt
-
~
!
_
:
r
~
t
_
m
_
~
!
~
_J
.
-
~
·
L.
-,I
~
J
f~l!-11-1
~
Rear
J
••L
I
••R
1
~
-----
--
-·
7 When
setting
is
complete,
click
[Close
Window].
•
To
restore the channel which is currently being adjusted
to
the
default, click [Ch. Flat].
To
restore all the channels to the initial
settings, click [All Reset]. Click [OK] when each confirmation
message
appears.
•
When Tweeter is selected
for
"Front
1"
to protect the speaker, there
is no filter off(Slope OFF) setting
for
HPF There is no filter
off
(Slope OFF) setting
for
Subwoofer
LPF,
either.
• When the speaker
is
set to the "OFF" mode, the X-Over
for
that
speaker cannot be
set. Refer
to
"Setting the Speaker System (Output
System
Select)" (page 13)1 "Setting the Speakers (Speaker Setup)/
Setting the
Subwoofers" (page 14).
• Check the playback frequencies
of
the connected speakers before
adjusting.
•
After the setting, it
is
recommended to store the setting contents on
the
unit. For details, refer
to
"Storing the Preset Values (Preset
Store)" (page 12).
27-EN
To Next Page
Loading...
