Alpine PXA-H800 - RoadEQ Operation; Audio Setup;Adjustment

6
Rotate
the
[Rotary encoder] to
select "Auto TCR,"
and then press the [Rotary encoder].
'·
The
AUTO
TCR screen
is
displayed.
7
Press the [Rotary encoder].
Countdown will
start.
,_
Ill
AUTO
TCR
("d
l
!lUi:J'lirm
1
>'t.:HI
<
'
<m
::iff
10
51:![
During the
10
second countdown,
go
outside the vehicle
and
close
the door.
A test
signal will
be output from the speakers to measure the
acoustic characteristics of the cabin.
Do
not open any
doors
until
the screen indicates
"Finished."
If
external
noise
interferes with the measurement, the
"Calibration Error"
message
will
appear on the screen.
In
this case, click
[Rotary encoder] again tore-measure.
o
If
you want
to
stop measurement, press [
~
].
o
If
the microphone is not connected,
"NoMic"
will be displayed and
the measureme
nt
will not be carried out.
Press
[~}or
[Rotary
Encoder] to cancel the indication.
8
When
"Finished"
appears, press [Rotary encoder].
o
This function is not available when Defeat is
set
to
ON.
o
Measurement
of
Auto TCR takes approximately 5 minutes.
o
Auto TCR measurement result overwrites the manual TCR
measurement result.
o
Sound
may arrive
at
the listening position
at
slightly different times,
depending on the speaker and enclosure.
To
compensate
for
this, the
distance can be adjusted to be larger than the actual distance.
o
After the setting, it is
re
co
mmended to store the setting contents on
the unit.
For
details, refer
to
"Storing
the
Pr
eset Values (Preset
Store)"
(page 36).
Adjusting
for
Road
Noise
(Road
EO)
Road.EQ (REAL-
TIME
OPTIMIZED ADAPTIVE DRIVING EQ) is a
function to automatically adjust the
EQ
properties in accordance with
the road noise while driving.
The
Road Equalizer compensates for constantly changing noise, so
always keep the microphones connected.
1
Preparing for measurement.
•
Pa
rk the
vehicle
in a quiet
l
ocation.
• Close
doors, windows, sunroof, etc.
•
Turn
the air-conditioner and heater
OFF.
•
Turn
off
th
e engine of the
vehicl
e.
2
Preparing the microphone.
Refer to the
insta
ll
ation m
an
ual.
3 Turn the ignition switch of the
vehicle
to ACC (On).
•
If
an air-conditioner or heater is turned on, turn it
off
Measureme
nt
should not be performed
if
air
-conditioner
or
heater noise is
pr
esent.
4
Press [FUNC.].
From
the
Commander
5 Rotate the [Rotary encoder] to
select "RoadEQ;'
and
then press the [Rotary encoder].
6
Rotate the [Rotary encoder] to
select "Calibration,"
and then press the [Rotary encoder].
The
CALIBRATION
screen is
displayed.
7 Press the [Rotary encoder].
Countdown
will
start.
During the
10
second countdown,
go
outside the vehicle
and
close the door.
A test signal will
be output from the speakers to measure the
acous
ti
c characteristics of the cabin. Do not open any
doors
until the screen indicates
"Finished." If external
noise
interferes with the measurement, the "Calibration Error"
message
will
appear on the screen.
In
this case,
c
li
ck
[Rotary encoder] again
tore
-measure.
o
If
you want to stop measurement, press [
~
].
o
If
the microphone is not connected,
"N
oMic"
will be displayed
and
the measurement will not be carried out. Press [
~
]
or
[Rotary
Encoder] to cancel the indication.
8
When "Finished"
appears, press [Rotary encoder].
o
This function is not available when Defeat is set to
ON.
o
Measurem
en
t
of
RoadEQ takes approximately
7
minutes.
o
When you select
"Calibration"
again, the previous setup data will be
erased when count-down is started.
o
Measureme
nt
values will not be lost in the event the system is reset
or
battery power is disconnect
ed
.
When automatic measurement is completed, Road.EQ can be turned on
or
off
and its level
ca
n be selected.
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select "Road EQ,"
and then press the [Rotary encoder].
3 Rotate the [Rotary encoder] to select "Level
Adjustment,"
and then press the [Rotary encoder].
The
LEV
EL ADJUSTMENT screen is
displayed.
4
-EN