6 Press [
~
] twice to go back to the screen for Step
3.
7 Rotate the [Rotary encoder] to select "Level
Adjustment," and then press the [Rotary encoder].
8 Select the source for the head unit
by
rotating the
[Rotary encoder], and press the [Rotary encoder].
,,
,l''"'l,
~I',
I
CO/Compressed Data/FM/Digital Radio/DVD/AUX/Others
9 Select the level you want by rotating the [Rotary
encoder], and press the [Rotary encoder].
MX Plus level increases
in
the following order: 1
~
2
~
3.
FM
(Level1 to
3,
OFF):
The
medium
to
high frequencies become clearer, and produces well
balanced
sound
at
all
frequencies.
CD (Level1 to
3,
OFF):
CD
mode processes a large amount
of
data during playback.
MX
takes advantage of this large data quantity
to
reproduce a more
clear,
clean output.
Compressed Data/Digital Radio (Level 1 to
3,
OFF):
This
corrects information that
was
lost at the time of compression.
This reproduces a
well-balanced sound close
to
the
original.
DVD (Cinema, Action, Music, OFF):
Cinema:
Movie dialogue
is
clearly reproduced. Action movies
are
reproduced with more powerful sound.
Action:
Action movies
are
reproduced with
more
powerful sound.
Music:
Lower register sounds (drums, bass, etc.)
and
vocals
are
emphasized for clean
and
clear output.
AUX
I Others (Compressed, Music, DVD, OFF):
MX
mode suitable for
the
media (Compressed Data, Music,
DVD)
can be selected.
10
To adjust another source,
press[~]
and repeat
Steps 8 through 9.
•
You
can listen with Defeat
OFF
(adjusted setup values)
or
with
Defeat
ON
(Initial value) to compare, by following the steps below.
1 Press and
hold the [Rotary Encoder] for 2 seconds or
longer while
in
the adjustment mode.
2 Rotate the [Rotary Encoder] to switch on/off Defeat, and
listen to compare.
3
To
exit, select "OFF" and then press [
~
]
11
When the setting is complete, press and hold [
~]
for at least 2 seconds.
•
If
[
~
]
is
pressed during setting, the unit returns to the previous
item.
•
To
enable this function, Defeat should be is
set
to ON.
•
After
the setting, it is recommended
to
store the setting contents on
the unit. For details, refer to
"Storing the Preset Values (Preset
Store)"
(page 36).
From
the Commander
Setting
the
MX
Plus
(Standalone
Mode)
MX (Media X pander) Plus enhances the vocal and instrumental sounds
for music sources such
as
radio/CD/MP3, by generating harmonics lost
during digital processing. This high frequency compensation adds
clarity and detail normally lost to road noise.
In the Standalone mode, MX Plus does not become linked with the
source
of
the head unit. MX Plus should be set for each external input.
MX Plus mode will be switched, linked with the source switching
of
PXA-H800.
1 Press [FUNC.].
2 Rotate the [Rotary encoder] to select "MX Plus," and
then press the [Rotary encoder].
3 Rotate the [Rotary encoder] to select "MX Plus
Setup," and then press the [Rotary encoder].
+
'lf
iV
¥)7'
-·
~--~--
4 Rotate the [Rotary encoder] to select "ON," and then
press the [Rotary encoder].
IIJ
MX
PLUS
SETUP
.g,,
A
,~~
-~-
---
;t·~
"¥:,'
: . -
--~
0~-
. . -
When you select [OFF],
MX
Plus for all music sources
becomes
disabled.
If an Ai-NET compatible head unit is connected, go to
Step
5.
If an Ai-NET compatible head unit is not connected, go to
Step
6.
5 Rotate the [Rotary encoder] to select "Standalone,"
and then press the [Rotary encoder].
• When a
head
unit without the
MX
Plus linking function is connected,
this should
be
set as "Standalone," even
if
it is an
Ai-NET
compatible
head
unit.
6 Press [
~
] once or twice to go back to the screen
for Step 3.
7 Rotate the [Rotary encoder] to select "Level
Adjustment," and then press the [Rotary encoder].
-
}~-
f
_':,x_fQ
8 Select the source for each external input by rotating
the [Rotary encoder], and press the [Rotary
encoder].
45-EN
To Next Page
Loading...
