Aritech CS875 - Page 161

To Next Page

To Previous Page

CS175-275-575-875 Installation Guide 161

Static Impulse

Single loop 4k7: Disarmed Quiet

Short Armed Change status

Open: No reaction No reaction

Dual loop 9k4 Disarmed Quiet

4k7 Armed Change status

Short or totally

open

Tamper Tamper

Main Page

Default Chapter3
- Table of Contents3
1 Introducing the Csx75 System7
2 Default Codes9
3 Default Country Codes10
4 Installation Guidelines11
- Installing the System11
- Wiring the System11
- Basic Installation Procedure12
- Installation Schematic14
Installing the Control Unit15
- CS575M/CS875M (Large Metal Housing)15
- CS275/CS575/CS875 (Polycarbonate Housing)17
- CS175M/CS275M/CS575SM (Small Metal Housing)19
- Control Unit Wiring Diagram: CS-17522
  - Inputs and Outputs23
- Control Unit Wiring Diagram: CS-27524
  - Inputs and Outputs25
- Control Unit Wiring Diagram: CS-575 and CS-87526
  - Inputs and Outputs27
5 LCD - LED Keypad28
- Installing the Keypad29
- Mounting the Keypad29
- Wiring the Keypad30
- Wiring the Keypads Together30
6 Wiring Zones32
- General32
- Dual Wiring32
- Single Wiring32
7 Wiring Sounders33
- Wiring a Sounder with EOL Protection33
8 Wiring Fire Detectors36
- General36
  - 4-Wire Fire Detector (CS275-575-875)36
  - 4-Wire Fire Detector (CS175)37
- Fire Escape Planning37
9 Wiring the Outputs38
10 Programming the System40
- Enrolling Modules and Keypads40
- Programming the LCD Keypads40
- Programming the LED Keypads45
11 Programming Modules and Locations50
- Parts of the System50
- Programming Data50
  - Numerical Data (ND)50
  - Feature Selection Data (FSD)50
12 Programming the Panel52
- Default Programming52
- Entering Programming Mode52
- Selecting a Module to Program52
- Loading Factory Defaults for the Controller52
- Defining the Country Code53
- Programming Via the LED Keypad53
- Programming Via the LCD Keypad54
13 Programming with Up/Download Software56
- General56
  - Wiring of the RS232 Cable56
- Programming56
14 Control Panel Programming Locations57
15 Using Partitioned Systems88
- Leds in Partitioning Master Mode88
- Displays in the Partitioning Master Mode88
16 Setting up RF Zones - Rx8I4-16I491
- Setting the DIP Switches91
- Module Status Conditions92
- Wiring the Rx8I4-16I492
  - Specifications92
- Programming the Rx8I4-16I493
17 Setting up RF Zones - Rx8W8-16W898
- Setting the DIP Switches99
- Module Status Conditions99
- Wiring the Rx8W8-16W899
  - Terminal Description99
  - Specifications100
- Programming the Rx8W8 - Rx16W8100
18 CS216 Hardware Zone Expander106
- Setting the DIP Switches106
  - DIP Switch 6107
- Wiring the CS216107
  - Terminal Description107
  - Specifications108
- Programming the CS216108
  - Programming the Zone Configuration and Partition108
19 CS534 Audio Board109
- Features Definition109
- Wiring the CS534110
  - Terminal Description110
  - Specifications111
- General Operating Instructions111
- Line-Hold or Call Back111
- Programming the CS534114
  - Programming the CS534 Parameters114
20 CS507 Ouput Expander Board118
- Setting the DIP Switches119
  - DIP Switch 4119
- Wiring the CS507119
  - Terminal Description119
  - Specifications120
- Programming the CS507121
  - Programming the Output Configuration and Partition121
21 CS586 RS232 Interface127
- Wiring the CS586127
  - Terminal Description127
  - Specifications128
- General Operating Instructions128
  - LED Indications128
- Programming the CS586128
  - Programming the RS232 Parameters128
22 Control Panel Programming Worksheets130
23 Appendix 1: Reporting Fixed Codes in Contact ID and SIA145
24 Appendix 2: Reporting Zone Codes in Contact ID and SIA147
25 Appendix 3: Overview of Module Numbers149
- Keypads149
- Hardware Expander CS216149
- Output Module CS507149
- Wireless Receiver (Rx8W8 and Rx16W8)150
- Wireless Receiver (RX8I4)150
26 Appendix 4: Service Messages151
27 Glossary152
28 Technical Specifications160
- Keyswitch Zones160
29 Tasks Summary162
30 Index163

Aritech CS875 - Page 161

Table of Contents

Related product manuals