Aritech CS875

To Next Page

To Previous Page

CS175-275-575-875 Installation Guide 21

6. Add the pillars for the CS216 input expander or CS507 output expander to the main

board.

7. Mount the CS216 input expander or CS507 output expander.

8. Wire the keypad bus for all modules. See the modules for wiring instructions.

9. Connect the battery and power up the panel.

Main Page

Default Chapter3
- Table of Contents3
1 Introducing the Csx75 System7
2 Default Codes9
3 Default Country Codes10
4 Installation Guidelines11
- Installing the System11
- Wiring the System11
- Basic Installation Procedure12
- Installation Schematic14
Installing the Control Unit15
- CS575M/CS875M (Large Metal Housing)15
- CS275/CS575/CS875 (Polycarbonate Housing)17
- CS175M/CS275M/CS575SM (Small Metal Housing)19
- Control Unit Wiring Diagram: CS-17522
  - Inputs and Outputs23
- Control Unit Wiring Diagram: CS-27524
  - Inputs and Outputs25
- Control Unit Wiring Diagram: CS-575 and CS-87526
  - Inputs and Outputs27
5 LCD - LED Keypad28
- Installing the Keypad29
- Mounting the Keypad29
- Wiring the Keypad30
- Wiring the Keypads Together30
6 Wiring Zones32
- General32
- Dual Wiring32
- Single Wiring32
7 Wiring Sounders33
- Wiring a Sounder with EOL Protection33
8 Wiring Fire Detectors36
- General36
  - 4-Wire Fire Detector (CS275-575-875)36
  - 4-Wire Fire Detector (CS175)37
- Fire Escape Planning37
9 Wiring the Outputs38
10 Programming the System40
- Enrolling Modules and Keypads40
- Programming the LCD Keypads40
- Programming the LED Keypads45
11 Programming Modules and Locations50
- Parts of the System50
- Programming Data50
  - Numerical Data (ND)50
  - Feature Selection Data (FSD)50
12 Programming the Panel52
- Default Programming52
- Entering Programming Mode52
- Selecting a Module to Program52
- Loading Factory Defaults for the Controller52
- Defining the Country Code53
- Programming Via the LED Keypad53
- Programming Via the LCD Keypad54
13 Programming with Up/Download Software56
- General56
  - Wiring of the RS232 Cable56
- Programming56
14 Control Panel Programming Locations57
15 Using Partitioned Systems88
- Leds in Partitioning Master Mode88
- Displays in the Partitioning Master Mode88
16 Setting up RF Zones - Rx8I4-16I491
- Setting the DIP Switches91
- Module Status Conditions92
- Wiring the Rx8I4-16I492
  - Specifications92
- Programming the Rx8I4-16I493
17 Setting up RF Zones - Rx8W8-16W898
- Setting the DIP Switches99
- Module Status Conditions99
- Wiring the Rx8W8-16W899
  - Terminal Description99
  - Specifications100
- Programming the Rx8W8 - Rx16W8100
18 CS216 Hardware Zone Expander106
- Setting the DIP Switches106
  - DIP Switch 6107
- Wiring the CS216107
  - Terminal Description107
  - Specifications108
- Programming the CS216108
  - Programming the Zone Configuration and Partition108
19 CS534 Audio Board109
- Features Definition109
- Wiring the CS534110
  - Terminal Description110
  - Specifications111
- General Operating Instructions111
- Line-Hold or Call Back111
- Programming the CS534114
  - Programming the CS534 Parameters114
20 CS507 Ouput Expander Board118
- Setting the DIP Switches119
  - DIP Switch 4119
- Wiring the CS507119
  - Terminal Description119
  - Specifications120
- Programming the CS507121
  - Programming the Output Configuration and Partition121
21 CS586 RS232 Interface127
- Wiring the CS586127
  - Terminal Description127
  - Specifications128
- General Operating Instructions128
  - LED Indications128
- Programming the CS586128
  - Programming the RS232 Parameters128
22 Control Panel Programming Worksheets130
23 Appendix 1: Reporting Fixed Codes in Contact ID and SIA145
24 Appendix 2: Reporting Zone Codes in Contact ID and SIA147
25 Appendix 3: Overview of Module Numbers149
- Keypads149
- Hardware Expander CS216149
- Output Module CS507149
- Wireless Receiver (Rx8W8 and Rx16W8)150
- Wireless Receiver (RX8I4)150
26 Appendix 4: Service Messages151
27 Glossary152
28 Technical Specifications160
- Keyswitch Zones160
29 Tasks Summary162
30 Index163

Table of Contents

Related product manuals