1
O&M Manual (Rev-H)
Table of Contents
SAFETY ................................................................ IV
WARNINGS ............................................................ IV
HAZARDOUS LOCATION INSTALLATION ......................... IV
PART1 - INTRODUCTION ....................................... 5
1.1 GENERAL .................................................... 5
1.2 H10 SMART SENSORS ................................... 6
1.3 SPECIFICATIONS ............................................ 8
PART 2 – MECHANICAL INSTALLATION .................. 9
2.1 TRANSMITTER MOUNTING ............................. 9
2.2 ENCLOSURE DIMENSIONS ............................... 9
2.3 WALL AND PIPE MOUNTING ......................... 10
2.4 PANEL MOUNTING (REMOTE SENSORS ONLY).. 12
2.5 DUCT SENSOR MOUNTING ........................... 12
2.6 DUCT MOUNT (INTEGRAL) ........................... 14
2.7 GENERATOR INSTALLATION/REMOVAL ............ 14
PART 3 – ELECTRICAL CONNECTIONS................... 15
3.1 TRANSMITTER CONNECTIONS ........................ 15
3.2 TERMINAL BOARD - SENSOR CONNECTIONS ..... 16
3.3 TERMINAL BOARD – LOOP POWER CONNECTIONS
17
3.4 HEATED SENSOR HOUSING WIRING ............... 18
3.5 REMOTE SENSOR WIRING ............................ 19
3.6 HEATED SENSOR WIRING (AC OR VDC POWERED)
20
3.7 HEATED REMOTE SENSOR WIRING (2-WIRE) ... 21
3.8 DUCT MOUNT SENSOR WIRING .................... 22
3.9 SENSOR CONNECTIONS WITH 6 FT CABLE ........ 22
3.10 AC OR 12-30 VDC POWERED ...................... 23
3.11 RELAY CONFIGURATION ............................... 24
3.12 REMOTE RESET INPUT ................................. 24
3.14 WIRING EXAMPLES ..................................... 25
3.15 AC OR 12-30 VDC POWERED ...................... 26
3.16 HART POINT-TO-POINT (2-WIRE) ................ 28
3.17 COMMUNICATIONS JUMPER SETTING ............. 29
PART 4 - OPERATION ........................................... 30
4.1 OPERATOR INTERFACE PANEL .............................. 30
Menus and Settings ......................................... 30
Moving the Cursor and Selecting ..................... 30
Editing Settings ................................................ 30
4.2 STARTUP ......................................................... 31
Transmitter Review .......................................... 31
Sensor Review .................................................. 32
Generator Review ............................................ 33
4.3 MAIN DISPLAY ................................................. 34
Main Reading ................................................... 34
Trouble Indication ........................................... 35
Timed Return to Main Display ......................... 35
Inhibiting Alarms from the Main Display ........ 35
4.4 POP-UP DISPLAYS ............................................. 35
Sensor Removed Display.................................. 35
Sensor Installed ............................................... 35
Generator Removed ........................................ 36
Generator Installed.......................................... 36
4.5 MAIN MENU ................................................... 37
Main Menu ...................................................... 37
Alarm Active Menu .......................................... 37
4.6 SETUP MENU .................................................. 37
4.7 SENSOR MENUS, METHODS, AND SETTINGS .......... 38
Sensor Menu .................................................... 38
Sensor Settings Menu ...................................... 38
Sensor Model Menu ........................................ 38
Sensor Range Menu ......................................... 39
Sensor Calibration ........................................... 40
Sensor Calibration Menu ................................. 41
Sensor Auto-test .............................................. 44
4.8 ALARM MENUS, METHODS, AND SETTINGS ........... 48
Alarms Menu ................................................... 48
Gas Level Alarms ............................................. 48
Trouble Alarm .................................................. 53
Alarm Inhibit .................................................... 57
Alarm Test Menu ............................................. 58
4.9 DATA-LOG MENUS, METHODS, AND SETTINGS ...... 59
Data Log Menu ................................................ 59
Data Log Setup Menu ...................................... 60
Data Log View Menu ....................................... 60
Data Log Print Menus, Methods, and Settings 62
4.10 I/O MENUS, METHODS AND SETTINGS .............. 64
I/O Menu ......................................................... 64
4-20mA Output ................................................ 64
4.11 COM MENUS AND SETTINGS ....................... 66
Relay Operation, Menus, and Settings ............ 70
4.11 PANEL MENUS, METHODS, AND SETTINGS .......... 72
Panel Menu ..................................................... 72
Display Menu ................................................... 72
Security Menu .................................................. 73
4.12 SYSTEM MENU .............................................. 77
Clock Menu ...................................................... 77
Reset Menu ..................................................... 77
Version Menu .................................................. 78
PART 5 – MAINTENANCE .................................... 79
PART 6 – SPARE PARTS ....................................... 81
To Next Page
Loading...
Need help?
General