EasyManuals Logo

AudioCodes MSBG Series User Manual

AudioCodes MSBG Series
1195 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1074 background imageLoading...
Page #1074 background image
User's Manual 1074 Document #: LTRT-27045
Mediant 1000B Gateway & E-SBC
62.10.6 PSTN Parameters
This subsection describes the device's PSTN parameters.
62.10.6.1 General Parameters
The general PSTN parameters are described in the table below.
Table 62-56: General PSTN Parameters
Parameter Description
Trunk Name
config-voip > interface
<e1|t1|bri> name
[DigitalPortInfo_x]
Defines an arbitrary name for a trunk (where x denotes the trunk
number for the ini file parameter). This can be used to help you
easily identify the trunk.
The valid value is a string of up to 40 characters. The following
special characters can be used (without the quotes):
ï‚§ " " (space)
ï‚§ "." (period)
ï‚§ "=" (equal sign)
ï‚§ "-" (hyphen)
ï‚§ "_" (underscore)
ï‚§ "#" (pound sign)
By default, the value is undefined.
Protocol Type
configure voip > interface e1-
t1|bri > protocol
[ProtocolType]
Defines the PSTN protocol for all the Trunks. To configure the
protocol type for a specific Trunk, use the ini file parameter
ProtocolType_x:
ï‚§ [0] NONE
ï‚§ [1] E1 EURO ISDN = ISDN PRI Pan-European (CTR4)
protocol
ï‚§ [2] T1 CAS = Common T1 robbed bits protocols including E&M
wink start, E&M immediate start, E&M delay dial/start and loop-
start and ground start.
ï‚§ [3] T1 RAW CAS
ï‚§ [4] T1 TRANSPARENT = Transparent protocol, where no
signaling is provided by the device. Timeslots 1 to 24 of all
trunks are mapped to DSP channels.
ï‚§ [5] E1 TRANSPARENT 31 = Transparent protocol, where no
signaling is provided by the device. Timeslots 1 to 31 of each
trunk are mapped to DSP channels.
ï‚§ [6] E1 TRANSPARENT 30 = Transparent protocol, where no
signaling is provided by the device. Timeslots 1 to 31,
excluding time slot 16 of all trunks are mapped to DSP
channels.
ï‚§ [7] E1 MFCR2 = Common E1 MFC/R2 CAS protocols
(including line signaling and compelled register signaling).
ï‚§ [8] E1 CAS = Common E1 CAS protocols (including line
signaling and MF/DTMF address transfer).
ï‚§ [9] E1 RAW CAS
ï‚§ [10] T1 NI2 ISDN = National ISDN 2 PRI protocol
ï‚§ [11] T1 4ESS ISDN = ISDN PRI protocol for the
Lucentâ„¢/AT&Tâ„¢ 4ESS switch.
ï‚§ [12] T1 5ESS 9 ISDN = ISDN PRI protocol for the
Lucentâ„¢/AT&Tâ„¢ 5ESS-9 switch.

Table of Contents

Other manuals for AudioCodes MSBG Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AudioCodes MSBG Series and is the answer not in the manual?

AudioCodes MSBG Series Specifications

General IconGeneral
BrandAudioCodes
ModelMSBG Series
CategoryGateway
LanguageEnglish

Related product manuals