EasyManuals Logo

AudioCodes MSBG Series User Manual

AudioCodes MSBG Series
1195 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1088 background imageLoading...
Page #1088 background image
User's Manual 1088 Document #: LTRT-27045
Mediant 1000B Gateway & E-SBC
Parameter Description
ï‚§
[65536] EXPLICIT PRES SCREENING = The calling party
number (octet 3a) is always present even when
presentation and screening are at their default.
Note: This option is applicable only to ETSI, NI-2, and
5ESS.
ï‚§ [131072] STATUS INCOMPATIBLE STATE = Clears the
call on receipt of Q.931 Status with incompatible state.
Otherwise, no action is taken (default).
ï‚§ [262144] STATUS ERROR CAUSE = Clear call on receipt
of Status according to cause value.
ï‚§ [524288] ACCEPT A LAW =A-Law is also accepted in
5ESS.
ï‚§ [2097152] RESTART INDICATION = Upon receipt of a
Restart message, acEV_PSTN_RESTART_CONFIRM is
generated.
ï‚§ [4194304] FORCED RESTART = On data link
(re)initialization, send RESTART if there is no call.
ï‚§ [67108864] NS ACCEPT ANY CAUSE = Accept any Q.850
Cause IE from ISDN.
Note: This option is applicable only to Euro ISDN.
ï‚§ [134217728] NS_BRI_DL_ALWAYS_UP (0x08000000) =
By default, the BRI D-channel goes down if there are no
active calls. If this option is configured, the BRI D-c
hannel is
always up and synchronized.
ï‚§ [536870912] = Alcatel coding for redirect number and
display name is accepted by the device.
Note: This option is applicable only to QSIG (and relevant
for specific Alcatel PBXs such as OXE).
ï‚§ [1073741824] QSI ENCODE INTEGER = If this bit is set,
INTEGER ASN.1 type is used in operator coding (compliant
to new ECMA standards); otherwise, OBJECT IDENTIFIER
ASN.1 type is used.
Note: This option is applicable only to QSIG.
ï‚§ [2147483648] 5ESS National Mode For Bch Maintenance
=
Use the National mode of AT&T 5ESS for B-channel
maintenance.
Note:
ï‚§ To configure the device to support several ISDNIBehavior
features, enter a summation of the individual feature values.
For example, to support both [512] and [2048] features, set
the parameter ISDNIBehavior is set to 2560 (i.e., 512 +
2048).
ï‚§ When configuring through the Web interface, to select the
options click the arrow button and then for each required
option select 1 to enable.
ï‚§ For BRI terminal endpoint identifier (TEI) configuration,
instead of using the ISDNIBehavior parameter, use the
following parameters: BriTEIConfigP2P_x,
BriTEIConfigP2MP_x, BriTEIAssignTrigger_x, and
BriTEIRemoveTrigger_x.
[ISDNIBehavior_x] Same as the description for parameter ISDNIBehavior, but for
a specific trunk ID.

Table of Contents

Other manuals for AudioCodes MSBG Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AudioCodes MSBG Series and is the answer not in the manual?

AudioCodes MSBG Series Specifications

General IconGeneral
BrandAudioCodes
ModelMSBG Series
CategoryGateway
LanguageEnglish

Related product manuals