EasyManuals Logo

AudioCodes MSBG Series User Manual

AudioCodes MSBG Series
1195 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1101 background imageLoading...
Page #1101 background image
Version 7.2 1101 Mediant 1000B Gateway & E-SBC
User's Manual 62. Configuration Parameters Reference
Parameter Description
Remove Calling Name
rmv-calling-name
[RemoveCallingName]
Enables the device to remove the Calling Name from SIP-to-ISDN
calls for all trunks.
[0] Disable = (Default) Does not remove Calling Name.
[1] Enable = Removes Calling Name.
Note: Some PSTN switches / PBXs may not be configured to support
the receipt of the “Calling Name” information. These switches might
respond to an ISDN Setup message (including the Calling Name)
with an ISDN "REQUESTED_FAC_NOT_SUBSCRIBED" failure. The
parameter can be set to Enable (1) to remove the “Calling Name”
from SIP-to-ISDN calls and allow the call to proceed.
Remove Calling Name
configure voip > interface bri
> rmv-calling-name
[RemoveCallingNameForTrun
k_x]
Enables the device to remove the Calling Name for SIP-to-ISDN
calls, per trunk.
[-1] Use Global Parameter = (Default) Settings of the global
parameter RemoveCallingName are used.
[0] Disable = Does not remove Calling Name.
[1] Enable = Remove Calling Name.
Note: The x in the ini file parameter name denotes the trunk number,
where 0 is Trunk 1.
Progress Indicator to ISDN
configure voip > interface e1-
t1|bri > pi-to-isdn
[ProgressIndicator2ISDN_x]
Determines the Progress Indicator (PI) to ISDN per trunk.
[-1] Not Configured = (Default) The PI in ISDN messages is set
according to the parameter PlayRBTone2Tel.
[0] No PI = PI is not sent to ISDN.
[1] PI = 1; [8] PI = 8: The PI value is sent to PSTN in
Q.931/Proceeding and Alerting messages. Typically, the
PSTN/PBX cuts through the audio channel without playing local
ringback tone, enabling the originating party to hear remote Call
Progress Tones or network announcements.
Note: The x in the ini file parameter name denotes the trunk number,
where 0 is Trunk 1.
Set PI in Rx Disconnect
Message
configure voip > interface e1-
t1|bri > pi-in-rx-disc-msg
[PIForDisconnectMsg_x]
Defines the device's behavior per trunk when a Disconnect message
is received from the ISDN before a Connect message is received.
[-1] Not Configured = (Default) Sends a 183 SIP response
according to the received progress indicator (PI) in the ISDN
Disconnect message. If PI = 1 or 8, the device sends a 183
response, enabling the PSTN to play a voice announcement to the
IP side. If there isn't a PI in the Disconnect message, the call is
released.
[0] No PI = Doesn't send a 183 response to IP. The call is
released.
[1] PI = 1; [8] PI = 8: Sends a 183 response to IP.
Note: The x in the ini file parameter name denotes the trunk number,
where 0 is Trunk 1.
[ConnectOnProgressInd] Enables the play of announcements from IP to Tel without the need
to answer the Tel-to-IP call. It can be used with PSTN networks that
don't support the opening of a TDM channel before an ISDN Connect
message is received.
[0] = (Default) Connect message isn't sent after SIP 183 Session
Progress message is received.
[1] = Connect message is sent after SIP 183 Session Progress

Table of Contents

Other manuals for AudioCodes MSBG Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the AudioCodes MSBG Series and is the answer not in the manual?

AudioCodes MSBG Series Specifications

General IconGeneral
BrandAudioCodes
ModelMSBG Series
CategoryGateway
LanguageEnglish

Related product manuals