AUMA Aumatic ACExC 01.1 - Legend to Standard Wiring Diagram

AUMA Aumatic ACExC 01.1

68 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

22.1 Legend to standard wiring diagram

61

Actuator controls AUMATIC AC 01.1 / ACExC 01.1

Operation instructions DeviceNet

Table of Contents

Default Chapter2
- Table of Contents2
1 Safety Instructions4
- Range of Application4
- Commissioning (Electrical Connection)4
- Maintenance4
- Warnings and Notes4
2 Short Description4
3 Transport and Storage5
4 General Information about Devicenet5
- Devicenet Cable6
- Devicenet Topology6
- Devicenet Communication7
- Devicenet Object Model7
- Protection Functions8
5 Technical Data9
6 AUMATIC Devicenet Design13
7 Electrical Connection14
- Power Supply (Standard)14
- Remote Position Transmitter14
- AUMATIC on Wall Bracket14
- Fitting of the Connection Housing15
- Test Run15
- Check Limit and Torque Switching15
- Bus Connection (Standard)15
- Mains and Bus Connection for Explosion-Proof Version17
- Bus Cables19
- Setting the Devicenet Address and the Baud Rate Via the Local Controls20
- Further Parameters of the Devicenet Interface23
8 Commissioning with Controls Introduction24
- Functions of the AUMATIC with Devicenet24
- Setting of the Devicenet Interface of the AUMATIC24
- Communication Model24
- Object Model of the AUMATIC24
- List of Objects Available in the AUMATIC25
- Bus Access25
- Explicit Messages25
- Poll I/O Connection25
- Configuration of the Poll I/O Connection Via the Local Controls25
- Configuration of the Poll I/O Connection Via the Devicenet Configuration Tool25
9 Poll I/O Data Interface of the AUMATIC26
- Description of the Input Data26
- Detailed Description of the Input Data31
- Description of the Output Data33
- Detailed Description of the Output Data34
10 Operation Parameters of the Actuator35
11 Description of Actuator Functions39
- Operation Commands for OPEN / CLOSE Operation39
- Positioner40
- Stepping Mode40
12 Safety Function40
13 Release Function of the Local Controls (Option)41
14 Additional Control Inputs (Option)42
15 Combination Fieldbus / Standard Interface (Option)44
16 EMERGENCY STOP Function (Option)45
17 Redundant Bus Connection with Component Redundancy (Option)47
- Settings for the Redundant Devicenet Interface 2 (Component Redundancy)47
- External Change-Over of the Communication Channels48
- Details of the Change-Over48
18 Indication and Programming of the AUMATIC49
- Software Parameters of the Devicenet Interface49
- Menu Indications49
19 Description Via Devicenet Interface52
- Assignment of the Customer Inputs of the Devicenet Interface (Option)53
- Devicenet Connection Assignment53
20 Trouble Shooting and Corrective Actions54
- Optical Signals During Operation54
- Status Indications in the Display55
- Devicenet Diagnosis Indication in the Display55
- Offline Connection Set of the AUMATIC56
- Reset of the AUMATIC to the Factory Settings56
- Actuator Can Not be Controlled Via Devicenet57
21 Appendix A EDS File59
22 Appendix B Standard Wiring Diagram60
- Legend to Standard Wiring Diagram61
23 Appendix C Proposed Wiring Diagrams62
24 Appendix D Literature References65
25 Appendix E Connection of the Screen for AUMATIC Acexc65
- Index67
- Addresses of AUMA Offices and Representatives68

Related product manuals

AUMA AUMATIC ACExC 01.2

Preview: AUMA AUMATIC AC 01.2

AUMA AUMATIC AC 01.2

Preview: AUMA AM 01.1

Preview: AUMA ACV 01.2

Preview: AUMA ABG 10.2

Preview: AUMA AMB 01.1

Preview: AUMA MATIC AM 01.1

AUMA MATIC AM 01.1

Preview: AUMA MATIC AM 02.1

AUMA MATIC AM 02.1

Preview: AUMA ACVExC 01.2 Series

AUMA ACVExC 01.2 Series

Preview: AUMA ACE C 01.2 Profinet Series

AUMA ACE C 01.2 Profinet Series