Barco DP2K SLP Series

Barco DP2K SLP Series

175 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

4. Physical installation

4. PHYSICAL INSTALLATION

About this chapter

This chapter describes how the m echan ical and electrical set up of your DP2K SLP-series projector has to be don e.

Overview

• Positioning the DP2K SLP -series projector at port window

• Connecting the projector with the power net

R5906847 DP2K SLP SERIES 02/06/2017

27

Table of Contents

Default Chapter5
- Table of Contents5
Safety7
- General Considerations8
- Important Safety Instructions10
- Product Safety Labels13
- High Brightness Precautions: Hazard Distance (HD)14
- HD for Fully Enclosed Projection Systems16
- HD in Function of Modifying Optics17
Getting Started19
- Installation Requirements20
- Unpacking the Projector22
- Initial Inspection24
- Communicator PC Version25
- Commander & Web Commander26
Installation Process27
- Installation Process Overview28
- Software Upgrade29
- Starting up and Adjusting the System30
Physical Installation31
- Positioning the DP2K SLP-Series Projector at Port Window32
- Connecting the Projector with the Power Net35
Lenses & Lens Selection37
- Available Lenses38
- Lens Selection39
- Lens Installation40
- Lens Removal41
- Lens Shift, Zoom & Focus42
Input & Communication45
- Introduction46
- Local Keypad47
- Projector Status49
- Integrated Cinema Processor (ICP)50
- HD-SDI Input Module (Optional)51
- Integrated Media Block/Server (Optional)54
- Cinema Controller55
Icmp57
- ICMP Introduction58
- Icmp Hdd60
- ICMP Communication Ports61
- ICMP Source Input Ports63
- ICMP Displayport Speciﬁcations64
- ICMP SDI Speciﬁcations66
- ICMP HDMI 2.0 Speciﬁcations70
- ICMP HDMI 1.4 Speciﬁcations73
- ICMP Status Leds75
- ICMP HDD Status Leds76
- ICMP Device Certiﬁcate78
- ICMP Conﬁguration Via Communicator80
- ICMP Reset81
- Obtaining the Barco ICMP Certiﬁcate82
- Removing a HDD from the ICMP83
- Installing a HDD into the ICMP84
Communicator Touch Panel87
- Communicator Touch Panel88
- Installing the Touch Panel Interface90
- Repositioning the Touch Panel Interface92
Starting up93
- Switching the DP2K SLP-Series on94
- Switching the DP2K SLP-Series off95
Scheimpﬂug97
- Scheimpﬂug Introduction98
- Scheimpﬂug Adjustment100
- Fixation of the Lens Holder Front Plate102
- Back Focal Length Adjustment104
Convergence109
- Convergence Controls110
- Preparing for Convergence Adjustment112
- Converging the Blue Pattern Onto the Red Pattern113
- Converging the Green Pattern Onto the Red Pattern114
- Closing off the Light Processor Compartment115
Color Calibration117
- Calibration Process118
- Color Gamut Calibration119
Preventative Maintenance Actions121
- Month Maintenance Actions122
- Month Maintenance Actions123
Maintenance Procedures125
- Check the Large Dust Filter126
- Check the Small Dust Filter128
- Vacuum Cleaning of the Dust Filters130
- Washing and Drying the Dust Filters131
- Cleaning the Lens132
- Cleaning the Exterior of the Projector133
- Authorization to Clear Security Warning on the Projector134
Removal and Installation of the Projector Covers135
- Removal of the Light Source Cover136
- Removal of the Rear Cover137
- Removal of the Top Cover138
- Removal of the Left Side Cover139
- Removal of the Top Cover Plate of the Light Processor Compartment140
- Removal of the Side Cover Plate of the Light Processor Compartment142
- Installation of the Side Cover Plate of the Light Processor Compartment143
- Installation of the Top Cover Plate of the Light Processor Compartment144
- Installation of the Left Side Cover145
- Installation of the Top Cover146
- Installation of the Rear Cover147
- Installation of the Light Source Cover148
Speciﬁcations149
- Speciﬁcations of the DP2K-8SLP Series150
- Speciﬁcations of the DP2K-10SLP Series151
- Dimensions of the DP2K SLP-Series Projector152
- Dimensions of the Universal Pedestal153
- Technical Regulations154
- A.5 Technical Regulations154
Pin Conﬁgurations155
- About General Purpose Inputs & Outputs (GPIO)156
- Pin Conﬁgurations of the Cinema Controller Communication Ports158
- Pin Conﬁgurations of the ICMP Communication Ports159
Environmental Information163
- Disposal Information164
- C.1 Disposal Information164
- China Rohs Compliance165
- Taiwan Rohs Compliance167
- Turkey Rohs Compliance168
- Hazards169
- C.5 Hazards169
- Production Address170
- C.6 Production Address170
- Contact Information171
- C.7 Contact Information171
Index173

Other manuals for Barco DP2K SLP Series

Service Manual410 pages

Related product manuals

Preview: Barco DP2K-S Series

Barco DP2K-S Series

Preview: Barco DP2K-12C

Preview: Barco DP2K-19B

Preview: Barco DP2K-23B

Preview: Barco DP2K-20C

Preview: Barco DP2K-20CLP

Barco DP2K-20CLP

Preview: Barco DP2K-36BLP

Barco DP2K-36BLP

Preview: Barco DP2K-10SLP

Barco DP2K-10SLP

Preview: Barco DP2K-E series

Barco DP2K-E series

Preview: Barco DP2K-C Series

Barco DP2K-C Series