Baumuller b maXX 1000 - Page 158

Parameter manual b maXX
®
1000
Document no. 5.07004.03 Baumüller Nürnberg GmbH
158
of 208
A
P0909 Source frequency for RS485 (Modbus) communication
interface (rpm)
-32768 to 32767
rpm
0 rpm 1:1 67
P0910 Source frequency for CANopen communication inter-
face (rpm)
0 to 36000 rpm 0 rpm 1:1 67
P0911 Speed multiplier CANopen/Modbus 0 to 1.00 100:1 68
P1000 Operation mode set value 1 to 249 6 1:1 68
P1004 QUICKSTOP reaction code (Hardware) 0 to 7 0 1:1 69
P1005 SHUTDOWN reaction code 0 to 3 0 1:1 69
P1007 Drive error reaction code 0 to 3 0 1:1 70
P1009 Reaction quickstop command (software) 0 to 255 0 1:1 70
P1010 Data set ID 0 to 65535 0 1:1 71
P1070 PG function selection (enable card) 0 to 3 0 1:1 71
P1071 PG pulse range 0 to 20000 Inc 600 Inc 1:1 71
P1072 PG proportional gain (P) 0.0 to 10.0 1.0 1:1 72
P1073 PG integral time 0.00 to 100.00 s 1.00 s 100:1 72
P1074 PG speed control output frequency limit 0.00 to 100.00 Hz 10.00 Hz 100:1 72
P1075 PG speed feedback signal display filter 0 to 9999 500 1:1 72
P1076 Detection time PG speed feedback signal fault 0.0 to 10.0 s 1.0 s 10:1 s 73
P1077 Feedback speed signal fault treatment 0 to 2 1 1:1 73
P1078 PG speed estimate filter 0 to 9999 1 1:2 73
P1079 Warning code 0 to 65535 0 1:1 74
P1090 Multi function input terminal (MI1, MI2) 0 to 2 0 1:1 75
P1091 Multi function input terminal (MI3) 0 to 24 1 1:1 76
P1092 Multi function input terminal (MI4) 0 to 24 2 1:1 79
P1093 Multi function input terminal (MI5) 0 to 24 23 1:1 79
P1094 Multi function input terminal (MI6) 0 to 24 24 1:1 79
P1095 Multi function input terminal (MI7) 0 to 24 0 1:1 80
P1096 Multi function input terminal (MI8) 0 to 24 0 1:1 80
P1097 Multi function input terminal (MI9) 0 to 24 0 1:1 80
P1098 Multi function input terminal (MI10) 0 to 24 0 1:1 80
P1099 Multi function input terminal (MI11) 0 to 24 0 1:1 80
P1100 Multi function input terminal (MI12) 0 to 24 0 1:1 80
P1101 Internal/external multi function input terminals selection 0 to 4095 0 1:1 81
P1102 Internal multi function terminal 0 to 4095 0 1:1 82
P1103 External multi function input contact selection 0 to 4095 0 1:1 84
P1104 Digital terminal input delay time 0 to 20 1 1:1 85
P1105 Display the status of external multi function input termi-
nals
0 to 4095 0 1:1 86
P1106 Display the status of multi function input terminals 0 to 4095 0 1:1 87
P1110 Multi function output relay (RA1, RB1, RC1) 0 to 21 8 1:1 89
P1111 Multi function output (photocoupler output MO1) 0 to 21 1 1:1 90
P1112 Multi function output terminal (MO2/RA2) 0 to 21 0 1:1 90
P1113 Multi function output terminal (MO3/RA3) 0 to 21 0 1:1 90
P1114 Multi function output terminal (MO4/RA4) 0 to 65535 0 1:1 90
P1115 Multi function output terminal (MO5/RA5) 0 to 21 0 1:1 90
Parameter Range Standard value Internal
standard-
ization
Page