BVL V-MIX Fix Plus

To Next Page

To Previous Page

Safety instructions

Translation of the Original Operating Manual

V-MIX Fix Plus

Fig. 2-7 and Fig. 2-8 V-MIX Fix Plus with cross conveyor at the rear

Main Page

Table of Contents5
User Information7
Purpose of this Operating Manual7
Storing the Operating Manual7
Locational Information in this Operating Manual7
Illustrations Used8
Terms Used9
Safety Instructions10
Working in a Safety-Conscious Manner10
Organizational Measures10
Responsibilities of the Owner11
Responsibilities of the Operator11
Qualification of the Personnel12
Intended Use13
Reasonably Foreseeable Misuse13
Product Safety14
Safe Operation of the Machine14
Safety Devices and Guards14
Structural Modifications14
Replacement and Wear Parts as Well as Auxiliary Supplies15
Warranty and Liability15
General Safety Instructions16
General Information on Safety and Accident Prevention16
Use of the Machine16
Hydraulic System17
Electrical System17
Cleaning, Maintenance and Repairs18
Action-Related Safety Instructions and Important Information19
Action-Related Safety Instructions19
Important Information20
Warnings and Instructions20
Warnings21
Instructions25
Positioning of Warnings and Instructions27
Risks Resulting from Failure to Observe the Safety Instructions and Warnings31
Technical Data32
V-MIX Fix Plus 6.5-1S to 15-1S32
V-MIX Fix Plus 13-2S to 25-2S33
Type Plate and CE Mark35
Hydraulic Unit35
Capacity Limits36
Operating Fluids36
Information on Noise Generation36
Design and Function37
Overview of the V-MIX Fix Plus37
V-MIX Fix Plus - Overview of Assemblies38
Mixing Hopper39
Ladder and Inspection Window39
Anti-Spill Ring40
Mixing and Dispenser Unit41
Mixing Auger with Cutting Blades42
Discharge Area (Discharge Opening)43
Conveyor Belt (Optional)44
Cross Conveyor (Optional)44
Counter Blades45
Weighing System (Optional)46
Hydraulic Unit (Optional)47
Electrohydraulic Control Block47
Hydraulic Hand Pump (Optional)48
Oilcooling49
Control Switch Cabinet50
Main Switch51
Emergency Stop Button51
Operating Elements and Controls52
Display53
Safety Devices and Guards55
Cover Aprons55
Block Ball Valve56
Motor and Main Drive Shaft Protective Plates56
Emergency Stop Button56
Transport, Setup, and Initial Commissioning57
Scope of Delivery as Supplied57
Loading and Unloading the Machine Using Lifting Devices58
Machine Setup59
Connecting the Electrical System61
Checking the Machine for Proper Operation61
Use and Operation62
Switching the Machine on62
Switching on after Emergency Stop or Fault62
Starting and Ending the Mixing Process63
Filling the Mixing Hopper64
Recommended Order During Filling65
Discharging Fodder66
Removing Clogs68
Starting and Ending Cleaning Mode69
Cleaning, Maintenance and Repairs70
Cleaning71
Lubricating71
Lubrication Points72
Maintenance Schedule - Overview73
Oil Change at the Gear Unit74
Gear Unit Brevini ECS151275
Gear Unit Brevini EM106576
Gear Unit Comer PGA160277
Reduction Gearbox Bvl 108960 (Special Equipment)78
Entering the Mixing Hopper79
Discharge Opening with Protruding Cover Apron80
Discharge Opening with Tight-Fitting Cover Apron (Optional)81
Discharge Opening with Tight-Fitting Cover Apron and Conveyor Belt (Optional)82
Installation and Positioning of the Mixing Augers82
Cutting Blades of the Mixing Auger83
Sharpening Cutting Blades83
Swiveling/Replacing Cutting Blades84
Hydraulic System85
Checking the Hydraulic Oil Level86
Refilling Hydraulic Oil86
Markings on Hydraulic Hose Lines87
Maintenance Intervals87
Inspection Points for Hydraulic Hose Lines87
Installing and Removing Hydraulic Hose Lines88
Conveyor Belt (Optional)89
Belt Connection89
Tensioning/Aligning the Conveyor Belt89
Tightening Torques for Bolt Joints90
Faults91
Appendix92
Supplied Third-Party Documents92
Circuit Diagrams92

BVL V-MIX Fix Plus - Page 30

Table of Contents

Other manuals for BVL V-MIX Fix Plus

Related product manuals