EasyManuals Logo

C-Data FD1216S User Manual

C-Data FD1216S
115 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #93 background imageLoading...
Page #93 background image
Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506
Website: www.cdatatec.com
86
FECswitch:Enable
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
LLIDEncrypttypeDBAProfileIDTrafficCARID
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
17.ONTbusinesstemplateconfiguration
17.1ontsrvprofile
Command
ontsrvprofile(profileidprofileid|profilenameprofilename)
noontsrvprofile(profileidprofileid|profilenameprofilename)
View configview
Parameter
profileid
The
serial number of EPON ONT business template .If you do not specify a template ID,
then the system will assign automatically a template ID and enter the corresponding mode.
profilename
ThenameofEPONONTbusinesstemplate.ThedefaulttemplatenameistheSRV‐
profile_x,“x”isatemplatenumber.
Description
Command is used to create and enter the EPON ONT business template pattern or enter a created
EPON ONT business template pattern. Template for EPON ONT business OMCI (ONT Management and
Control Interface) way to manage the ONT provide business channels configuration. ONT relevant
properties are configured centrallyon business templates,when processing the same business
configuration of ONT, it only once and saves the configuration work. When the ONT management mode
is the OMCI, when adding ONT ,you need bind the business templates of EPON ONT;if not specified, the
system will automatically bind ONT to the default business template 0. After the command executed
successfully, you can set the relevant properties of business template in the corresponding EPON ONT
business template.
Example
To create the EPON ONT business template with ID10, you can be referenced when adding ONT.
OLT(config)#ontsrvprofileprofileid10
OLT(ontsrvprofile10)#
Example
Delete the EPON ONT business template with ID 10
OLT(config)#noontsrvprofileprofileid10
17.2ontport
Command
ontport(etheth|potspots)
View srvprofileview

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the C-Data FD1216S and is the answer not in the manual?

C-Data FD1216S Specifications

General IconGeneral
BrandC-Data
ModelFD1216S
CategorySwitch
LanguageEnglish