Cisco Catalyst 2960-X User Manual

PurposeCommand or Action
include the input interface in the log entry. Logging is supported only
for router ACLs.
•
(Optional) Enter routing to specify that IPv6 packets be routed.
•
(Optional) Enter sequence value to specify the sequence number for
the access list statement. The acceptable range is from 1 to
4,294,967,295.
•
(Optional) Enter time-range name to specify the time range that
applies to the deny or permit statement.
(Optional) Define a TCP access list and the access conditions.{deny | permit} tcp
{source-ipv6-prefix/prefix-length | any | host
Step 5
Enter tcp for Transmission Control Protocol. The parameters are the same
as those described in Step 3a, with these additional optional parameters:
source-ipv6-address} [operator
[port-number]] {destination-ipv6-
• ack—Acknowledgment bit set.
prefix/prefix-length | any | host
destination-ipv6-address} [operator
• established—An established connection. A match occurs if the TCP
datagram has the ACK or RST bits set.
[port-number]] [ack] [dscp value]
[established] [fin] [log] [log-input] [neq {port
| protocol}] [psh] [range {port | protocol}]
• fin—Finished bit set; no more data from sender.
[rst] [routing] [sequence value] [syn]
[time-range name] [urg]
• neq {port | protocol}—Matches only packets that are not on a given
port number.
• psh—Push function bit set.
• range {port | protocol}—Matches only packets in the port number
range.
• rst—Reset bit set.
• syn—Synchronize bit set.
• urg—Urgent pointer bit set.
(Optional) Define a UDP access list and the access conditions.{deny | permit} udp
{source-ipv6-prefix/prefix-length | any | host
Step 6
Enter udp for the User Datagram Protocol. The UDP parameters are the
same as those described for TCP, except that the [operator [port]] port
source-ipv6-address} [operator [port-number]]
{destination-ipv6-prefix/prefix-length | any |
number or name must be a UDP port number or name, and the established
parameter is not valid for UDP.
host destination-ipv6-address} [operator
[port-number]] [dscp value] [log] [log-input]
[neq {port | protocol}] [range {port |
protocol}] [routing] [sequence value]
[time-range name]]
(Optional) Define an ICMP access list and the access conditions.{deny | permit} icmp
{source-ipv6-prefix/prefix-length | any | host
Step 7
Enter icmp for Internet Control Message Protocol. The ICMP parameters
are the same as those described for most IP protocols in Step 1, with the
source-ipv6-address} [operator [port-number]]
{destination-ipv6-prefix/prefix-length | any |
addition of the ICMP message type and code parameters. These optional
keywords have these meanings:
host destination-ipv6-address} [operator
[port-number]] [icmp-type [icmp-code] |
Catalyst 2960-X Switch Security Configuration Guide, Cisco IOS Release 15.0(2)EX
202 OL-29048-01
Configuring IPv6 ACLs
Configuring IPv6 ACLs

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g