EasyManuals Logo

D-Link xStack DES-3528 Series Cli Reference Guide

D-Link xStack DES-3528 Series
605 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #244 background imageLoading...
Page #244 background image
xStack® DES-3528/DES-3552 Series Layer 2 Managed Stackable Fast Ethernet Switch CLI Reference Guide
244
802.1X Commands (Including Guest VLANs)
The Switch implements the server-side of the IEEE 802.1X Port-based and Host-based Network Access Control. This
mechanism is intended to allow only authorized users, or other network devices, access to network resources by
establishing criteria for each port on the Switch that a user or network device must meet before allowing that port to
forward or receive frames.
Command Parameters
enable 802.1x
disable 802.1x
create 802.1x user <username 15>
delete 802.1x user <username 15>
show 802.1x user
config 802.1x auth_protocol [local | radius_eap]
config 802.1x fwd_pdu system [enable | disable]
config 802.1x fwd_pdu ports [<portlist> | all] [enable | disable]
config 802.1x authorization
attributes radius
[enable | disable]
show 802.1x { [auth_state | auth_configuration] ports {<portlist>} }
config 802.1x capability ports [<portlist> | all] [authenticator | none]
config 802.1x max_users [<value 1 – 448> | no_limit]
config 802.1x auth_parameter ports [<portlist> | all] [default | {direction [both | in] | port_control [force_unauth |
auto | force_auth] | quiet_period <sec 0-65535> | tx_period <sec 1-65535>
| supp_timeout <sec 1-65535> | server_timeout <sec 1-65535> | max_req
<value 1-10> | reauth_period <sec 1-65535> | max_users [<value 1-448> |
no_limit] | enable_reauth [enable | disable]}(1)]
config 802.1x init [port_based ports [<portlist | all>] | mac_based ports [<portlist> | all]
{mac_address <macaddr>}]
config 802.1x reauth [port_based ports [<portlist> | all] | mac_based [ports] [<portlist> | all]
{mac_address <macaddr>}]
config radius add <server_index 1-3> [<server_ip> | <ipv6addr>] key <passwd 32> [default |
{auth_port <udp_port_number 1-65535> | acct_port <udp_port_number 1-
65535> | timeout <int 1-255> | retransmit<int 1-20>}]
config radius delete <server_index 1-3>
config radius <server_index 1-3> {ipaddress [<server_ip> | <ipv6addr>] | key <passwd
32> | auth_port [<udp_port_number 1-65535> | default] | acct_port
[<udp_port_number 1-65535> | default] | timeout [<int 1-255> | default] |
retransmit [<int 1-20> | default]}
show radius
create 802.1x guest_vlan <vlan_name 32>
config 802.1x guest_vlan ports [<portlist> | all] state [enable | disable]
delete 802.1x guest_vlan <vlan_name 32>
show 802.1x guest_vlan
show auth_statistics {ports <portlist>}
show auth_diagnostics {ports <portlist>}

Table of Contents

Other manuals for D-Link xStack DES-3528 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the D-Link xStack DES-3528 Series and is the answer not in the manual?

D-Link xStack DES-3528 Series Specifications

General IconGeneral
BrandD-Link
ModelxStack DES-3528 Series
CategorySwitch
LanguageEnglish

Related product manuals