Deep Sea Electronics Plc DSE6120 MKII

DSE6110 MKII & DSE6120 MKII Operator Manual
057-236 ISSUE: 1 Page 4 of 94
3.1.1 DC SUPPLY, ESTOP INPUT, DC OUTPUTS & CHARGE FAIL INPUT ................. 29
3.1.2 ANALOGUE SENSORS, MPU, CAN ...................................................................... 30
3.1.3 DSENET® .............................................................................................................. 31
3.1.4 GENERATOR / MAINS VOLTAGE & FREQUENCY SENSING .............................. 31
3.1.5 CURRENT TRANSFORMERS ............................................................................... 32
3.1.5.1 CT CONNECTIONS ........................................................................................ 32
3.1.6 CONFIGURABLE DIGITAL INPUTS ...................................................................... 33
3.1.7 PC CONFIGURATION INTERFACE CONNECTOR ............................................... 33
3.2 TYPICAL WIRING DIAGRAM ....................................................................................... 34
3.2.1 DSE6110 MKII TYPICAL WIRING DIAGRAM (3 PHASE 4 WIRE) ......................... 35
3.2.2 DSE6120 MKII TYPICAL WIRING DIAGRAM (3 PHASE 4 WIRE) ......................... 36
3.3 ALTERNATE TOPOLOGY WIRING DIAGRAMS ......................................................... 37
3.3.1 GENERATOR ........................................................................................................ 37
3.3.2 MAINS (6120 MKII ONLY) ...................................................................................... 38
3.4 EARTH SYSTEMS ........................................................................................................ 39
3.4.1 NEGATIVE EARTH ................................................................................................ 39
3.4.2 POSITIVE EARTH ................................................................................................. 39
3.4.3 FLOATING EARTH ................................................................................................ 39
3.5 TYPICAL ARRANGEMENT OF DSENET® .................................................................. 40
4 DESCRIPTION OF CONTROLS .................................................................... 41
4.1 DSE6110 MKII .............................................................................................................. 42
4.2 DSE6120 MKII .............................................................................................................. 43
4.3 CONTROL PUSH-BUTTONS ....................................................................................... 44
4.4 VIEWING THE INSTRUMENT PAGES ......................................................................... 47
4.4.1 STATUS ................................................................................................................. 48
4.4.1.1 GENERATOR LOCKED OUT .......................................................................... 48
4.4.2 ENGINE ................................................................................................................. 49
4.4.3 GENERATOR ........................................................................................................ 50
4.4.4 MAINS (DSE6120 MKII ONLY)............................................................................... 50
4.4.5 EXPANSION .......................................................................................................... 51
4.4.6 ALARMS ................................................................................................................ 52
4.4.6.1 ECU ALARMS (CAN ERROR MESSAGE / DTC) ............................................ 53
4.4.7 EVENT LOG .......................................................................................................... 54
4.4.8 LCD INICATORS.................................................................................................... 55
4.4.9 USER DEFINED STRINGS .................................................................................... 55
4.4.10 ABOUT .................................................................................................................. 56
4.4.10.1 MODULE INFORMATION ............................................................................... 56
4.4.10.2 SUPPORT STRINGS ...................................................................................... 56
5 OPERATION .................................................................................................. 57
5.1 QUICKSTART GUIDE .................................................................................................. 57
5.1.1 STARTING THE ENGINE ...................................................................................... 57
5.1.2 STOPPING THE ENGINE ...................................................................................... 58
5.2 STOP/RESET MODE.................................................................................................... 59
5.3 MANUAL MODE ........................................................................................................... 60
5.3.1 STARTING SEQUENCE ........................................................................................ 60
5.3.2 ENGINE RUNNING ................................................................................................ 61
5.3.3 STOPPING SEQUENCE ........................................................................................ 61
5.4 TEST MODE ................................................................................................................. 62
5.4.1 STARTING SEQUENCE ........................................................................................ 62
5.4.2 ENGINE RUNNING ................................................................................................ 63
5.4.3 STOPPING SEQUENCE ........................................................................................ 63
5.5 AUTOMATIC MODE .................................................................................................... 64
5.5.1 WAITING IN AUTO MODE..................................................................................... 64
5.5.2 STARTING SEQUENCE ........................................................................................ 64
5.5.3 ENGINE RUNNING ................................................................................................ 65
5.5.4 STOPPING SEQUENCE ........................................................................................ 65
5.6 SCHEDULER ................................................................................................................ 66
5.6.1 STOP MODE ......................................................................................................... 66