module. If lamp still fails to light, replace lamp/ig-
niter assembly.
REMOVAL
HIGH INTENSITY DISCHARGE (HID) HEADLAMPS -
LOW BEAM
LAMP/IGNITER ASSEMBLY
The lamp/igniter are an assembly and will be ser-
viced and replaced as such.
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove front fender extension splash shield on
the respective side by removing the fasteners (Fig.
14). Remove wheel and tire assembly if extra room is
needed.
(5) Remove the three nuts to the headlamp access
panel and remove panel.
(6) Release the spring retainer to the lamp/igniter
assembly.
(7) Pull assembly straight out of headlamp unit.
(8) Disconnect the lamp/igniter assembly connector
from the lamp/igniter assembly.
BALLAST MODULE
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove front fender extension splash shield on
the respective side by removing the fasteners (Fig.
14). Remove wheel and tire assembly if extra room is
needed.
(5) Remove the three nuts to the headlamp access
panel and remove panel.
(6) Remove two retaining screws and bracket to
ballast module.
(7) Disconnect the igniter/lamp assembly connector
from ballast module and the ballast module feed con-
nector.
(8) Remove the ballast module from headlamp
access cover.
HIGH BEAM
(1) Open deck lid.
(2) Remove four bolts to battery compartment
cover and remove cover.
(3) Disconnect and isolate the battery negative
cable.
(4) Remove front fender extension splash shield on
the respective side by removing the fasteners (Fig.
14). Remove wheel and tire assembly if extra room is
needed.
(5) Remove the three nuts to the headlamp access
panel and remove panel.
(6) Remove the headlamp by turning 1/4 turn
counterclockwise and pulling straight out.
(7) Disconnect the electrical connector from the
headlamp and remove from vehicle.
INSTALLATION
CAUTION: Do not touch the glass of HID or halogen
lamps with fingers or other possibly oily surface.
Reduced lamp life will result.
HIGH INTENSITY DISCHARGE (HID) HEADLAMPS -
LOW BEAM
LAMP/IGNITER ASSEMBLY
The lamp and igniter are an assembly and will be
replaced as such.
(1) Connect the lamp/igniter assembly connector to
the lamp/igniter.
(2) Push the lamp/igniter assembly straight into
headlamp unit.
(3) Install the spring retainer across the igniter/
lamp assembly.
(4) Place the headlamp access cover into position
and install the three nuts. Torque nuts to 4 N·m (35
in. lbs.).
(5) Install the front fender extension splash shield
on the respective side by and the fasteners (Fig. 14).
If wheel and tire assembly was removed, install.
(6) Connect the battery negative cable.
(7) Place battery access cover into place and install
four bolts.
(8) Close deck lid.
(9) Verify vehicle and system operation.
(10) Verify headlamp unit aim. If adjustment is
necessary, (Refer to 8 - ELECTRICAL/LAMPS/
LIGHTING - EXTERIOR/HEADLAMP UNIT -
STANDARD PROCEDURE).
BALLAST MODULE
(1) Connect the feed and lamp/igniter connectors
to the ballast module.
(2) Install the bracket and two retaining screws to
the ballast module inside the headlamp access cover.
(3) Place the headlamp access cover into position
and install the three nuts. Torque nuts to 4 N·m (35
in. lbs.).
(4) Install the front fender extension splash shield
on the respective side by and the fasteners (Fig. 14).
If wheel and tire assembly was removed, install.
(5) Connect the battery negative cable.
8L - 10 LAMPS ZB
HEADLAMP (Continued)
To Next Page