Draytek Vigor2860 Series User Manual

Vigor2860 Series User’s Guide
594
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
i
i
p
p
m
m
a
a
x
x
n
n
a
a
t
t
u
u
s
s
e
e
r
r
This command is used to set the maximum number of NAT users.
ip maxnatuser user no
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
User no
A number specified here means the total NAT users that
Vigor router supports.
0 – It means no limitation.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> ip maxnatuser 100
% Max NAT user = 100
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
i
i
p
p
6
6
a
a
d
d
d
d
r
r
This command allows users to set the IPv6 address for your router.
ip6 addr -s [prefix] [prefix-length] [LAN|WAN1|WAN2|iface#]
ip6 addr -d [prefix] [prefix-length] [LAN|WAN1|WAN2|iface#]
ip6 addr -a [LAN|WAN1|WAN2|iface#]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
-s
It means to add a static ipv6 address.
-d
It means to delete an ipv6 address.
-a
It means to show current address(es) status.
-u
It means to show only unicast addresses.
prefix
It means to type the prefix number of IPv6 address.
prefix-length
It means to type a fixed value as the length of the prefix.
LAN|WAN1|WAN2|iface#
It means to specify LAN or WAN interface for such address.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> ip6 addr -a
LAN
Unicast Address:
FE80::250:7FFF:FE00:0/64 (Link)
Multicast Address:
FF02::2
FF02::1:FF00:0
FF02::1
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
i
i
p
p
6
6
d
d
h
h
c
c
p
p
r
r
e
e
q
q
_
_
o
o
p
p
t
t

Draytek Vigor2860 Series Specifications

General

Firewall Type	Stateful Packet Inspection (SPI)
VPN Support	IPSec, PPTP, L2TP, SSL VPN
DoS Protection	Yes
Intrusion Prevention System (IPS)	Yes
LAN Interfaces	4 x Gigabit Ethernet
User Authentication	Local, RADIUS, LDAP
VPN Tunnels	32
Management Interface	Web-based, CLI
Concurrent Sessions	50, 000
Content Filtering	URL Keyword Filtering, Web Content Filtering