DURKOPP ADLER 580 - Menu Item Continuous Operation

120 pages

To Next Page

To Previous Page

29.7.3 Menu item continuous operation (St.cont.operat.)

In this menu item the continuous operation mode can

be switched on/off.

Starting the continuous operation can be done via the query yes/no.

Caution Risk of injury !

Exercise utmost caution when running the continuous operation.

104

Main Page

Default Chapter1
- Installation Instructions1
- Service Instructions1
- General Safety Instructions4
- Table of Contents5
1 General Notes9
- Necessary Program Setting9
2 Adjusting the Locking Positions10
- General Notes10
- Looper and Spreader Eccentric11
- Thread Take-Up Disc12
- Throw Eccentric13
3 Needle Bar Positioning14
4 Aligning the Looper Turret16
5 Aligning the Needle Bar Parallel to the Looper Turret19
6 Transversal Motion of the Fabric Support Plate21
7 Longitudinal Motion of the Fabric Support Plate23
8 Clamping Plates25
- Inserted Clamping Plates25
- Aligning the Clamping Plates26
- Adjusting the Spreading27
- Height of the Fabric Clamps29
- Adjusting the Locking Plate30
- Locking of the Clamping Plates31
- Adjusting the Fabric Clamping Pressure32
9 Adjusting the Seam Width33
- Presetting the Seam Width33
- Needle Zero Position36
10 Cutting Knife (Eyelet Knife)37
- Position of the Cutting Knife37
- Setting Dimensions39
- Adjusting the Knife Parallel to the Cutting Block40
- Adjusting the Knife Parallel to the Cutting Block with "Multiflex" Machines41
- Cutting Block Adjustment42
- Adjusting the Cutting Block Position (Multiflex System)43
- Setting the Switch for the "Multiflex" Cutting System47
- Cutting Pressure48
- Cutting Duration48
11 Looper Height49
12 Adjusting the Loop Stroke50
13 Needle Bar Height52
14 Distance between Looper and Needle53
15 Needle Protection54
16 Spreader55
17 Spreader Plate56
18 Throat Plate57
19 Adjusting the Needle Thread Knife58
20 Adjusting the Fabric Clamps60
21 Thread Take-Up Spring62
22 Short Trimmer for Lower Thread (580-112000, 580-312000)63
- Function Sequence63
- Initial Position65
- Adjusting the Cutting Pressure / Clamping Pressure67
- Knife Change68
23 Long Trimmer for Looper Thread and Gimp (580-121000 und -321000)69
- Cutting Pressure and Cutting Motion69
- Adjusting the Knife Overlap70
- Position of the Looper Thread and Gimp Clamp73
- Thread Deflector74
24 Short Trimmer for Looper Thread and Gimp77
- Optional Equipment for Subclass 580-14100078
25 Gimp Pulling Device for Subclass 580-14100079
26 Thread Catcher80
- General Notes80
- Adjustment81
- Subsequent Fitting of the Thread Catcher83
27 Maintenance84
28 Annex85
- Adjusting Operations Without Head Cover85
- Fuses in the Control Box86
- Exchange of the Control86
- Adjusting the Contrast of the Control Panel86
29 Service Menu (Technician Level)87
- Activating the Service Menu87
- Quitting the Service Menu87
- Menu Structure88
- Menu Structure with Numbers90
- Menu Items Configuration Automatic Buttonholer92
- Loading Position92
- Menu Item Throw Width92
- Menu Item Thread Monitor93
- Menu Item Duty Cycle of Cutting Block93
- Menu Item Sewing Equipment94
- Menu Item Threading Mode95
- Menu Item Operation Mode95
- Menu Item Tension Data96
- Menu Item Multiflex97
- Menu Items Operating Configuration98
- Menu Item Language98
- Menu Item Push-Buttons98
- Menu Item Brightness of the Sewing Lamp99
- Menu Item Key Tones99
- Menu Items Test Functions Multitest100
- Menu Item Output Test101
- Menu Item Manual Input Test102
- Menu Item Automatic Input Test103
- Menu Item Sewing Motor Test104
- Menu Item Step Motor Test105
- Menu Item Flash Test106
- Menu Item RAM-Test106
- Menu Items Test Functions / Test Program Sewing Sequence107
- Menu Item Stop107
- Menu Item Reference Start107
- Menu Item Continuous Operation108
- Menu Item Events109
- Menu Item All Events109
- Menu Item Latest Events109
30 Error Messages110
31 Troubleshooting116

DURKOPP ADLER 580 - Menu Item Continuous Operation

Table of Contents

Related product manuals