Eaton PowerXL DH1 Series - Page 219

195
Appendix A—Description of parameters
POWERXL DH1 SERIES ADJUSTABLE FREQUENCY DRIVES MN040041EN—August 2019 www.eaton.com
Code Modbus ID Parameter Application RO/RW
P12.1.6 2538 FB Process Data Input 6 Sel 1,2,3 RW
Use this parameter to assign the Fieldbus Data Input Selections, parameter/monitor Para ID's can be
assigned to these registers and then writen over the desired Fieldbus Network Word for Process Data.
see Communication Manual MN040010EN for more details.
P12.1.7 2539 FB Process Data Input 7 Sel 1,2,3 RW
Use this parameter to assign the Fieldbus Data Input Selections, parameter/monitor Para ID's can be
assigned to these registers and then written over the desired Fieldbus Network Word for Process Data.
see Communication Manual MN040010EN for more details.
P12.1.8 2540 FB Process Data Input 8 Sel 1,2,3 RW
Use this parameter to assign the Fieldbus Data Input Selections, parameter/monitor Para ID's can be
assigned to these registers and then written over the desired Fieldbus Network Word for Process Data.
see Communication Manual MN040010EN for more details.
P12.2.1 1556 FB Process Data Output 1 Sel 1,2,3 RW
Use this parameter to accessing the Fieldbus Data Output Selections, parameter/monitor ID's can be
assigned to these registers and then read over the desired Fieldbus Network Word for Process Data.
Default Values for Process Data Out in Fieldbus(build table for below values)
Process Data Out1 - Output Frequency = ID 1
Process Data Out2 - Motor Speed = ID 2
Process Data Out3 - Motor Current = ID 3
Process Data Out4 - Motor Torque = ID 4
Process Data Out5 - Motor Power = ID 5
Process Data Out6 - Motor Voltage = ID 6
Process Data Out7 - DC Link Voltage = ID 7
Process Data Out8 - Active Fault Code = ID 28
see Communication Manual MN040010EN for more details.
P12.2.2 1557 FB Process Data Output 2 Sel 1,2,3 RW
Use this parameter to accessing the Fieldbus Data Output Selections, parameter/monitor ID's can be
assigned to these registers and then read over the desired Fieldbus Network Word for Process Data.
Default Values for Process Data Out in Fieldbus(build table for below values)
Process Data Out1 - Output Frequency = ID 1
Process Data Out2 - Motor Speed = ID 2
Process Data Out3 - Motor Current = ID 3
Process Data Out4 - Motor Torque = ID 4
Process Data Out5 - Motor Power = ID 5
Process Data Out6 - Motor Voltage = ID 6
Process Data Out7 - DC Link Voltage = ID 7
Process Data Out8 - Active Fault Code = ID 28
see Communication Manual MN040010EN for more details.
P12.2.3 1558 FB Process Data Output 3 Sel 1,2,3 RW
Use this parameter to accessing the Fieldbus Data Output Selections, parameter/monitor ID's can be
assigned to these registers and then read over the desired Fieldbus Network Word for Process Data.
Default Values for Process Data Out in Fieldbus(build table for below values)
Process Data Out1 - Output Frequency = ID 1
Process Data Out2 - Motor Speed = ID 2
Process Data Out3 - Motor Current = ID 3
Process Data Out4 - Motor Torque = ID 4
Process Data Out5 - Motor Power = ID 5
Process Data Out6 - Motor Voltage = ID 6
Process Data Out7 - DC Link Voltage = ID 7
Process Data Out8 - Active Fault Code = ID 28
see Communication Manual MN040010EN for more details.
P12.2.4 1559 FB Process Data Output 4 Sel 1,2,3 RW
Use this parameter to accessing the Fieldbus Data Output Selections, parameter/monitor ID's can be
assigned to these registers and then read over the desired Fieldbus Network Word for Process Data.
Default Values for Process Data Out in Fieldbus(build table for below values)
Process Data Out1 - Output Frequency = ID 1
Process Data Out2 - Motor Speed = ID 2
Process Data Out3 - Motor Current = ID 3
Process Data Out4 - Motor Torque = ID 4
Process Data Out5 - Motor Power = ID 5
Process Data Out6 - Motor Voltage = ID 6
Process Data Out7 - DC Link Voltage = ID 7
Process Data Out8 - Active Fault Code = ID 28
see Communication Manual MN040010EN for more details.