Ecolab DryExxEco Advanced-ETH

Questions and Answers

A
Alejandro WilsonAug 12, 2025
What to do if the Ecolab Control Unit pump is not running?
- G
  Gary TrujilloAug 12, 2025
  If the Ecolab Control Unit pump isn't running, several issues could be the cause. First, ensure the air supply is open, as the supply line might be blocked or closed. Another potential cause is a blocked muffler, which requires cleaning or replacement. The pressure line might also be blocked or closed, so cleaning or opening the valve is recommended. Blocked operating chambers could be the problem, and removing any contamination is the solution. Lastly, a faulty air control could be the reason, necessitating its replacement.
C
Cassandra PatrickAug 16, 2025
Why is my Ecolab Control Unit pump running irregularly?
- J
  John WoodsAug 16, 2025
  If the Ecolab Control Unit pump is running irregularly, it could be due to several reasons. The piston rings or air control might be worn, requiring replacement. A broken diaphragm is another possibility, which means you'll need to replace the diaphragms and clean the pump. The air control might also be dirty, so try cleaning or replacing it. Additionally, check for blockages in the valve ball or body and remove any foreign bodies. In some cases, ice formation can cause irregular running, which can be resolved by improving air treatment.
X
xthomasAug 19, 2025
How to get rid of air in the conveyed medium in Ecolab DryExxEco Advanced-ETH?
- A
  andrea13Aug 20, 2025
  If there's air in the conveyed medium in your Ecolab Control Unit, possible causes include a leaky suction line, which would need to be sealed. Another cause might be an empty container, so ensure the container is filled or replace it with a new one. A broken diaphragm can also introduce air, requiring replacement of the diaphragms. Lastly, cavitation in the exhaust line could be the issue; adjust the intake height or fit an intake air vessel if necessary.
S
Sarah HicksAug 23, 2025
How to fix reduced dosing output in Ecolab DryExxEco Advanced-ETH?
- K
  Kristy PattersonAug 23, 2025
  If you're experiencing reduced dosing output from your Ecolab Control Unit, the air control line might not be providing enough pressure. To resolve this, check the filter pressure regulator and the 3/2 way solenoid valve. Also, inspect the compressed air circuits.
L
Lisa BerryAug 27, 2025
What to do if there is no pressure build-up in Ecolab Control Unit product line?
- J
  Jeffrey ChristensenAug 27, 2025
  If there's no pressure build-up in the product line of your Ecolab Control Unit, start by checking the circuit pipes for leaks and eliminate them, and consider increasing the operating air pressure. Also, inspect the pressure release valve and clean or replace it if necessary.
D
dalealvaradoAug 31, 2025
Why is conveyed medium coming out of the muffler of my Ecolab DryExxEco Advanced-ETH Control Unit?
- M
  Mr. Patrick BurtonAug 31, 2025
  If the conveyed medium is coming out of the muffler in your Ecolab Control Unit, it's likely that the diaphragm is broken. You should replace the diaphragm and clean the pump.
T
Travis MartinSep 3, 2025
Why is there no suction from Ecolab Control Unit pump following repair?
- J
  Jason NealSep 3, 2025
  If there's no suction from the Ecolab Control Unit pump after a repair, it might be due to connections not being correctly secured; retighten and seal them. Also, check if the valve body was incorrectly inserted and correct its position.
S
Scott AdamsSep 7, 2025
Why does Ecolab Control Unit have insufficient suction when pump is running?
- S
  stephenmurphySep 7, 2025
  If the Ecolab Control Unit pump is running but there's insufficient suction, the pump might be running too fast. Try starting it more slowly.

Summary

Safety

General Safety Advice

Fundamental safety principles and precautions applicable to the system's operation.

Proper Use Guidelines

Definition of intended use and warnings against misuse of the system.

Personnel Requirements and Qualifications

Specifications for personnel training, skills, and responsibilities for safe operation.

PPE and Safety Symbols

Explanation of personal protective equipment requirements and safety warning symbols.

Indications of Risks

Details on potential hazards such as electrical risks, fire, slipping, and chemical exposure.

Environmental Protection Measures

Operator Obligations and Responsibilities

Legal and operational duties of the system operator for safety and compliance.

Installation, Maintenance, and Repair Procedures

Safe practices and requirements for installing, maintaining, and repairing the equipment.

Assembly

Lubo-DryExx Applicator Station

Overview of the applicator station's physical assembly and setup.

Type 182830: ALMATEC Pump Assembly

Type 182831: WILDEN Pump Assembly

DryExxEco Control Unit Assembly

Instructions for assembling the control unit's switch cabinet.

Functional Description

DryExx System Overview

General description of the DryExx system's components and operation.

DryExxEco Control Unit Description

Detailed explanation of the control unit's features, functions, and capabilities.

Lubrication Function Description

Explanation of how the lubrication circuit operates and delivers lubricant.

Applicator Station Construction Details

Description of the physical build and components of the applicator station.

Connection

Pneumatic Connection Procedures

Chemical Connection Procedures

Electrical Connection: Control Unit

Instructions for safely wiring the control unit to power and signals.

Operation with Residual Current Protective Device

Commissioning and Operation

Commissioning the DryExx System

Step-by-step guide for initial setup and startup of the DryExx system.

Filling the Pipe System

Commissioning the Control Unit

Steps for setting up and configuring the DryExxEco control unit.

System Parameterisation Process

System Operation Modes

Belt Lubricant Failure; Container Change

Procedures for responding to low lubricant levels and changing containers.

Power Supply Failure Handling

DryExxEco Control Operation

HMI Display Overview

Introduction to the Human Machine Interface (HMI) and its basic operation.

Configuration Overview

Initial Configuration and Passwords

Software Display Layout

Programming Structure Overview

Home Screen Navigation

System Settings Management

Accessing and managing various system configuration parameters.

Circuit Parameters Configuration

General Parameters Configuration

System Messages and Alerts

Maintenance

Routine Maintenance Tasks

ALMATEC Pump Maintenance Procedures

WILDEN Pump Maintenance Procedures

Troubleshooting

General Troubleshooting Guide

ALMATEC Pump Troubleshooting

Specific fault diagnosis and solutions for the ALMATEC pump.

WILDEN Pump Troubleshooting

Specific fault diagnosis and solutions for the WILDEN pump.

Error Codes: DryExxEco Control

Explanation of error messages displayed by the control unit and their resolution.

Spare Parts

Ecolab DryExxEco Advanced-ETH Specifications

General

Product Type	Control Unit
Model Name	DryExxEco Advanced-ETH
Manufacturer	Ecolab
Communication	Ethernet
Communication Protocol	TCP/IP
Intended Use	Monitoring and controlling cleaning processes
Compatibility	Compatible with Ecolab cleaning systems