Edge-Core ECS4310-26T - SECTION I GETTING STARTED

To Next Page

To Previous Page

– 15 –

ECTION

GETTING STARTED

This section provides an overview of the switch, and introduces some basic

concepts about network switches. It also describes the basic settings

required to access the management interface.

This section includes these chapters:

◆ "Introduction" on page 17

◆ "Initial Switch Configuration" on page 23

Main Page

Default Chapter5
- About this Guide5
- Contents7
  - Table of Contents7
- Figures11
- Tables13
Sectioni15
- Key Features17
- Table 1: Key Features17
- Description of Software Features18
- System Defaults21
- Table 2: System Defaults21
Getting Started15
1 Introduction15
2 Initial Switch Configuration23
- Connecting to the Switch23
- Changing a Pc's IP Address27
Ection29
Web Configuration29
3 Using the Web Interface31
- Connecting to the Web Interface31
- Navigating the Web Browser Interface32
4 System Settings37
- Displaying System Information37
- Ystem Etting37
- Figure 7: System Information38
- Figure 8: System Password39
- Setting a User Account39
- Setting an IP Address40
- P Ort Etting45
5 Port Settings45
- Figure 11: Port Configuration47
6 Link Aggregation49
- General Link Aggregation Guidelines49
- Creating Trunk Groups50
- Figure 12: Trunk Group Setting51
- Configuring Trunk Settings52
- Figure 13: Trunk Distribution Algorithm Setting53
- Configuring LACP54
- Figure 14: LACP Port Configuration55
7 Creating Vlan S57
- IEEE 802.1Q Vlans57
- Assigning Ports to Vlans58
- Figure 15: VLAN Membership Configuration59
- Configuring VLAN Attributes for Port Members60
- Figure 16: VLAN Port Configuration60
8 Vlan Stacking61
- Configuring IEEE 802.1Q Tunneling61
- VLAN Stacking Table62
- VLAN Stacking Settings63
- Figure 17: VLAN Stacking Table63
- Figure 18: VLAN Stacking Settings64
9 Igmp Snooping65
- IGMP Snooping Introduction65
  - Multicast Entry Table66
  - IGMP Snooping Setting67
10 Spanning Tree71
- Configuring the Spanning Tree Protocol71
- Configuring STP Global Settings72
- Figure 22: STP Global Setting74
- Configuring STP Port Settings75
- Table 5: Recommended STP Path Cost Range75
- Table 6: Recommended STP Path Costs75
- Table 7: Default STP Path Costs76
- Figure 23: STP Port Setting78
11 Quality of Service79
- Qos Introduction79
- Port-Based Priority80
- DSCP-Based Priority81
- Figure 24: Port-Based Priority Setting81
- Priority-To-Queue Mapping82
- Figure 25: DSCP-Based Priority Setting82
- Table 8: Default Mapping of Cos Values to Egress Queues82
- Table 9: Cos Priority Levels83
- Packet Scheduling84
- Figure 26: Priority-To-Queue Mapping84
- Figure 27: Packet Scheduling85
12 Link Layer Discovery Protocol87
- Configuring LLDP87
- Figure 28: LLDP Settings88
- LLDP Neighbors89
- Table 10: LLDP System Capabilities89
- Figure 29: LLDP Neighbors90
13 Snmp Settings91
- Simple Network Management Protocol91
- Setting SNMP System and Community Strings92
- Specifying SNMP Trap Receivers93
- Figure 30: SNMP Settings93
- Figure 31: SNMP Trap Receiver Settings94
14 Port Mirroring95
- Figure 32: Port Mirroring96
- P Ort Ecurity97
15 Port Security97
- Figure 33: Port Security98
16 Bandwidth Control99
- Figure 34: Bandwidth Control100
- Figure 35: Jumbo Frame Setting101
17 Jumbo Frame101
18 Management Access Filter103
- Figure 36: Management Access Filter104
19 Mac Address Security105
- MAC Forwarding Table105
- Static MAC Addresses106
- Figure 37: MAC Address Forwarding Table106
- MAC Address Filtering107
- Figure 38: Static MAC Setting107
- Figure 39: MAC Address Filtering108
20 1X Security109
- Configuring 802.1X Authentication109
- X Global Settings110
- Figure 40: 802.1X Setting111
- X Port Settings111
- Figure 41: 802.1X Port Setting112
21 General Security Settings113
- G Eneral S Ecurity S Ettings113
- IP Filter Security113
- Figure 42: IP Filter Setting114
- Storm Control Setting114
- Figure 45: Defence Engine Setting117
- P Ort S Tatistics119
- Figure 46: Port Statistics120
22 Port Statistics121
- HTTP Upgrade121
- M Anagement T Ools121
- Figure 47: Software Upgrade122
- Figure 48: Restoring Factory Defaults122
- Figure 49: Reboot Switch123
- Resetting the Switch123
- Management Features128
- Standards128
- Management Information Bases129
- Table 11: Troubleshooting Chart131
- Problems Accessing the Management Interface132
- G Lossary133
23 Managementtools121

Edge-Core ECS4310-26T - SECTION I GETTING STARTED

Table of Contents

Other manuals for Edge-Core ECS4310-26T

Related product manuals