ELTEX MES3108 - Page 106

106 MES3000 Ethernet switch series
no lldp med network-policy
number
Remove network-policy rule from this interface.
lldp med location {coordinate
coordinate | civic-address
civic_address_data | ecs-elin
ecs_elin_data}
coordinate: 16 bytes;
civic_address_data:
(6..160) bytes;
ecs_elin_data: (10..25)
bytes
Specify the device location for LLDP ('location' parameter value of
LLDP MED).
- coordinate—address in coordinate system
- civic_address_data—device administrative address
- ecs_elin_data—address in ANSI/TIA 1057 format
no lldp med location
Remove location parameter settings.
lldp med notification
topologychange {enable |
disable}
-
Enable/disable sending LLP MED notifications on topology
changes.
- enable—send notifications
- disable—do not send notifications
no lldp med notifications
topology-change
Restore the default value.
LLDP packets received through the link aggregation group is saved individually by group ports
that have received these messages. LLDP sends separate messages to each port of the group.
LLDP operation is independent from STP state for the port; LLDP packets are sent and
received via ports blocked by STP.
If the port is controlled via IEEE 802.1x, LLDP works only with authorized ports.
Privileged EXEC mode commands
All commands are available to the privileged user.
Command line request in privileged EXEC mode appears as follows:
console#
Table 5.106 —Privileged EXEC mode commands
Command
Value/Default value
Action
clear lldp table
-
Clear address table for discovered neighbouring devices and start
a new packet exchange cycle via LLDP MED.
show lldp configuration
[gigabitethernet gi_port |
tengigabitethernet te_port]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4).
Show LLDP configuration on all device physical interfaces, or on
specified interfaces only.
show lldp med configuration
[gigabitethernet gi_port |
tengigabitethernet te_port]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4).
Show LLDP MED extension configuration for all physical interfaces,
or specified interfaces only.
show lldp local
{gigabitethernet gi_port |
tengigabitethernet te_port}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4).
Show LLDP information announced by this port.
show lldp local
tlvsoverloading
[gigabitethernet gi_port |
tengigabitethernet te_port]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4).
Show TLVs LLDP restart state.
show lldp neighbors
[gigabitethernet gi_port |
tengigabitethernet te_port]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4).
Show information on the neighbouring devices with the active
LLDP.
show lldp statistics
[gigabitethernet gi_port |
tengigabitethernet te_port]
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4).
Show LLDP statistics.
Example execution of commands
 Define the following TLV fields for 1/g1 port: port-description, system-name, system-
description. Add control address 192.168.17.55 for this interface
console(config)# configure
console(config-if)# lldp optional-tlv port-desc sys-name sys-desc
console(config-if)# lldp management-address 192.168.17.55