ELTEX MES3108 - Page 119

MES3000 Ethernet switch series 119
VLAN interface configuration mode commands
Command line request in VLAN interface configuration mode appears as follows:
console(config-if)#
Table 5.123 —VLAN interface configuration mode commands
Command
Value/Default value
Description
bridge multicast mode
{macgroup | ipv4-group |
ipv4-src-group}
-/mac-group
Define the multicast data transmission mode.
- mac-group—multicast transmission based on VLAN and MAC
addresses
- ipv4-group—multicast transmission with the filtering type based
on VLAN and the recipient address in IPv4 format
- ip-src-group—multicast transmission with the filtering type
based on VLAN and the sender address in IPv4 format
no bridge multicast mode
Restore the default value.
bridge multicast address
[mac_multicast_address |
ip_multicast_address] [[add |
remove] { gigabitethernet
gi_port | tengigabitethernet
te_port |port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Add multicast MAC address to the multicast addressing table and
statically add or remove interfaces to/from the group.
- mac_multicast_address—multicast MAC address
- ip_multicast_address—multicast IP address
- add—add static subscription to multicast MAC address for
Ethernet port or port group range
- remove—remove the static subscription to multicast MAC
address
Interface listing should be delimited with '–' and ','
no bridge multicast address
[mac_multicast_address |
ip_multicast_address]
Remove multicast MAC address from the table.
bridge multicast forbidden
address
[mac_multicast_address |
ip_multicast_address] {add |
remove} {gigabitethernet
gi_port | tengigabitethernet
te_port |port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Disable the connection for configured port(s) to multicast IPv6
address (MAC address).
- mac_multicast_address—multicast MAC address
- ip_multicast_address—multicast IP address
- add—add port(s) into the banned list
- remove—remove port(s) from the banned list Interface listing
should be delimited with '–' and ','
no bridge multicast forbidden
address
[mac_multicast_address |
ip_multicast_address]
Remove the banning rule for the multicast MAC address.
bridge multicast forward-all
{add | remove}
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..12)
Transmission of all
multicast packets is
denied by default.
Enable the transmission of all multicast packets on the port.
- mac_multicast_address—multicast MAC address
- add—add ports/aggregated ports into the port list, that allows all
multicast packets transmission
- remove—remove the port group/aggregated ports from the
allowing rule
Interface listing should be delimited with '–' and ','.
no bridge multicast forward-all
Restore the default value.
bridge multicast forbidden
forward-all {add | remove}
{gigabitethernet gi_port |
tengigabitethernet te_port |
port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Ports are allowed to
dynamically join the
multicast group by
default.
Deny the port to dynamically join the multicast group.
- add—add ports/aggregated ports into the port list, that denies
all multicast packets transmission
- remove—remove the port group/aggregated ports from the
denying rule.
Interface listing should be delimited with '–' and ','.
no bridge multicast forbidden
forward-all
Restore the default value.
bridge multicast ip-address
ip_multicast_address [[add |
remove] {gigabitethernet
gi_port | tengigabitethernet
te_port | port-channel group}
gi_port: (1..8/0/1..24);
te_port: (1..8/0/1..4);
group: (1..24)
Register IP address in the multicast addressing table and statically
add/remove interfaces to/from the group.
- ip_multicast_address—multicast IP address
- add—add ports to the group
- remove—remove ports from the group
Interface listing should be delimited with '–' and ','.
no bridge multicast ip-address
ip_multicast_address
Remove multicast IP address from the table.